Question about Dodge Ram 2500

1 Answer

99 dodge ram 2500 brake light on the dash stays on... and its not the speed sensor... any help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Dodge Expert
  • 652 Answers

Check the ground on the e brake mechisemsingle wire black connector

Posted on Nov 14, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 154 Answers

SOURCE: location of speed sensor a for 99 dodge intrepid

The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Posted on Apr 02, 2009

RudolfDiesel
  • 100 Answers

SOURCE: What is a Code 84

Hello
Welcome to FY
I would check your speed sensor located on the rear end this is on top of the housing this will throw that code too.
RD

Posted on Jan 12, 2009

  • 90 Answers

SOURCE: i have 1998 dodge ram my abs and brake light came on

IIRC, the speedo reads off of the sensor in the center section of the rearend. Also controls ABS. Hope this helps!

Posted on Dec 25, 2008

  • 701 Answers

SOURCE: where is oil pressure sensor located on 2001 dodge 2500 cummins?

Hello mhak330: My name is Roger and I can give you the answer to your question. Locate the ECM on the drivers side of the engine.look for the bottom bolt holding the ECM. To the right of the bolt you should see the oil pressure sender unit. Should you need further help please just ask. Please rate the quality of your answer. This way we know you received helpful information. Thank You for using Fix Ya. Roger

Posted on Jul 07, 2009

  • 1 Answer

SOURCE: 2001 dodge ram 2500 abs light stays on and soo doe

I had the same problem and it turned out to be one of the front speed sensors and the rear speed sensor as well. If you get a chance to look at all the speed sensors make sure the wires on the front aren't burnt from hot brakes. I have an 01 3500 4X4 and it was a pain to change the front sensor but the rear sensor took about 5-10 minutes, it's located in the middle of of the rear axle right on top. I bought both of mine on Ebay and cut the price in half.

Posted on Aug 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I apply the brakes on my Dodge 2500 they sometimes push back and the ABS light comes on the dash, why?


You have a abs problem. Most likely a wheel speed sensor. Have system scanned for codes. The reason the pedal pushing back is system detected a skid. Brakes should work fine though

Sep 26, 2015 | 2001 Dodge Ram 2500 Truck

1 Answer

I have a 1995 dodge ram 2500 cummins the abs and brake lights are on and the cruise control is not working? I have replaced the master cylinder and the speed sensor in the rear axle


The warning lights mean there should be a trouble code stored in the body computer. I would start there.
When the ABS system is inop it may prevent the cruise from working too. Sometimes a hydraulic brake system failure will turn the ABS light on too. After repairs you would need to scan the system to turn the light off with most vehicles.
Are the brake lights in the rear of the truck staying on ?

Jul 03, 2012 | 1995 Dodge Ram 2500

2 Answers

I gotta 2005 dodge ram 2500 4x4 3/4 ton i uplugged he front abs sensor from wheel hub assembly and now abs light is on what do i do to clear the light


you cannot clear light while sensor is unplugged. the light is on because the computer is not seeing a reading for the wheel speed. when the light comes on your brakes will operate normally but you will not have any anti lock brakes so take care not to lock up your brakes during hard braking.

Feb 17, 2011 | 2005 Dodge Ram 2500 Truck

2 Answers

I Have a 2002 Dodge Ram 2500.Both the ABS and Brake Lights are on


Hi!!

Did you have the ABS sensors checked ?? The brake fluid level when low also activates the Brake and ABS lights?? Drive truck to an AutoZone store and ask to have computer codes scanned. This is a free service for all customers. This will help you to pinpoint the problem.

Good Luck!!

Don't forget to rate this post.

Jun 04, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

I Have a 2002 Dodge Ram 2500.Both the ABS and Brake Lights are on


Does the speedometer work? Out might have a bad speed sensor in the rear axle. Did you have it scanned for codes?

Jun 04, 2010 | 2002 Dodge Ram 3500 Truck

2 Answers

Just my speed guage does not work and abs light and parking brake light stay on on my 99 ram 1500


you have an code stored in the abs module.likely a bad rear wheel speed sensor.as it runs the speedometer.check wiring to the sensor.it is located on the top of the rear diff housing.hope this helps.

Sep 09, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Hello, I have a 2001 dodge ram 1500 5.9 ltr 4WD. My spedometer stopped working. My check engine, ABS, and break lamps on the dash are all on. Shortly after my spedometer stopped working It seemed like my...


have you tried to replace the speed sensor in the rear end my 99 durango did basically the same thing speedo wasnt working right brake lights on dash check engine light on

Jul 27, 2009 | Dodge Ram 1500 Cars & Trucks

1 Answer

Brake light stuck on


Are you refering to the brake light on the dash? If so check the brake fluid level in the master cylinder. If the fluid is low it will cause the brake light to stay on.

Apr 13, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

What is a Code 84


Hello
Welcome to FY
I would check your speed sensor located on the rear end this is on top of the housing this will throw that code too.
RD

Jan 10, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

Lights staying on


speed sensor prob went bad. it's at the tail end of the transmission on the drivers side

Jun 14, 2008 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...