Question about 1999 Ford Expedition

Open Question

Case fuse transfer drive

Where is transfer case fuse located

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 GMC suburban actuator and fuse location. There is not one on front differential and no place for fuse in fuse block. 4 wheel will not engage. No owners manual


The actuator will not be on the front differential or drive line, it will be on the transfer case, which is mounted behind the transmission. Follow the front drive shaft back from the front differential, and the component at the rear of the driveshaft is the transfer case. That is where four wheel drive is engaged/disengaged.
I'm not familiar with your vehicle, but if you have a separate lever to engage 4wd, there will not be a fuse for the actuator - it is a manual system. If the 4wd is selected electrically, check that all wiring and connectors on the transfer case are in good condition.

Sep 25, 2016 | 1990 GMC Suburban

1 Answer

How do I fix my 99 blazer the dome lights won't turn on and the 4 who drive won't light up or work


In the instrument panel fuse box fuse # 8 CTSY LP 10A ,that's for the dome lights, fuse panel is left side of IP. What are you talking about 4 who drive won't light up or work ? 4 wheel drive ? Do you have two speed automatic or two speed selectable ?
Switch Indicator Lamps Do Not Light - One or More ? Check fuse #15 IP fuse box 10A 4WD . This is for two speed auto !

Circuit Description

The indicator lamps circuits consist of 5 individual lamps contained inside the mode/range switch assembly, they are AUTO, 4WD, 2HI, 4HI, 4LO and NEUTRAL. The AUTO, 4WD, 2HI, 4HI, and 4LO lamps are contained inside their respective range button. When the ignition is ON, the transfer case shift control module illuminates the indicator lamp that corresponds to the current ATC gear position by providing a ground through a current limiting driver.
The transfer case shift control module flashes each indicator lamp after a shift has been requested and will continue to flash until the transfer case shift control module can complete the shift. After a shift to AUTO, 4WD, 2HI, 4HI, or 4LO is made, the transfer case shift control module will flash that indicator lamp until the transfer case shift control module receives a high voltage signal on CKT 1695 from the front axle switch.
A solid state circuit located inside the switch supplies ignition voltage to the lamps. The solid state circuit also receives voltage whenever the headlamp switch is in park or headlamp position. When the solid state circuit receives voltage from the headlamp switch it will reduce the voltage that it supplies to the indicator lamps, dimming the lamps when the headlamps are ON.

Feb 07, 2015 | Cars & Trucks

3 Answers

99 Ford F-150 won't go into 4wheel drive I looked undernieth and front drive shaft is not turning


Someone will have to go under and check the linkage is working when the 4 wheel drive is fully engaged and not just moved to a neutral position.

Dec 04, 2014 | Ford Cars & Trucks

2 Answers

Were do I locate four wheel drive actuator relay on 2002 Ford ranger four wheel drive


The entire assembly is mounted to the back of the transfer case, it contains all the parts except the control module.

Jan 25, 2012 | 2002 Ford Ranger Regular Cab

2 Answers

Where is fuse for 4 wheel drive located on 1986 jeep cherokee pioneer


Hello,

The fuse of this car is located under the hood of the car. It is a box covered in some kind of plastic casing, you will have to pry open the cover to be able to locate the fuse of this car.

Hope this was helpful. Thank You for Using FixYa!!!

Jan 14, 2011 | 1986 Jeep Cherokee

1 Answer

The 4 wheel drive select switch stopped working is it the switch or could it be a fuse


Sounds like the transfer case motor is bad.(located on transfercase beside front drive shaft yoke) 7"Long skinny motor outside transfer case.I had the same problem on my 93 S10 blazer , 4L60 E ( first year for the electronic transmission ) .changed it and is working fine now

Jan 03, 2011 | 2002 Chevrolet TrailBlazer

4 Answers

Four-wheel drive will not work and is not transfer case, could be a fuse?


IT COULD BE A FUSE THERE ARE FUSES UNDER THE HOOD FOR 4 WHEEL DRIVE ALSO IF THAT DOED NOT WORK CHECK 4 WHEEL DRIVE SELINOID

Dec 13, 2009 | 2002 Chevrolet TrailBlazer

2 Answers

I have a 1998 chevy blazer (s-10) 4.3L 4x4 it keeps blowing the #15 (10amp) 4wd fuse, if you put a 10 amp fuse in it will blow the minute you turn it on ,then we put a 15 amp in it seems to do it when you...


check transfer case electrical switch, sometime if it bad it will also blow the fuse. don't recommend you put any higher fuse than recommend, If the fuse blow there is a short some where and by putting higher amp fuse you might short or burn something else beside the fuse. if that check out than check your transfer case motor, might lock up and not allowing the motor to turn instead it short the fuse. don't drive the car, just leave it in park, put correct fuse amp back in and unplug transfer case electric switch and turn the key on (dont start the car) and see if the fuse blow; if not plug it back in and see if it blow the fuse. if that is not the case, unplug transfer case wire, and do the same and see if it blow the fuse.

Jul 12, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

4 Wheel drive won't kick in on my 2001 Ford 350 4 wheel drive


do check the fuse, should be located in the fuse box in the engine compartement, refer to your owner's manual as to where this fuse is located, if the fuse is good, check the electrical connections on the transfer case, if that's good, check the oil in the transfer case to do so, towards the back of the transfer case there are two big looking bolts placed in diagonal to eachother one higher than the other, on the higher one loosen and unscrew if oil ouses out its good or by sticking your little finger in the hole and you can touch the oil it's good.... if all that is good check for a kinked vacuum hose on the battery side up against the firewall it should be a green tube and a red tube, if thats good, the last thing to check is the fork system on the front diff I've often seen them seized, fortunately I've been lucky to have unseize them with loose nut and lubrication...

goodluck

Dec 16, 2008 | 2001 Ford F350 Super Duty SuperCab

Not finding what you are looking for?
1999 Ford Expedition Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...