Question about 1993 Chevrolet S-10 Blazer

1 Answer

Remove dash board 1993 chevy blazer - 1993 Chevrolet S-10 Blazer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 880 Answers

Lots of work and lots of little pieces. works best with two people sitting side by side removing their pieces and catalogging the fasteners

Posted on Nov 03, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

danowilliams
  • 104 Answers

SOURCE: dash board is digital and the dash lights went out

Remove the 5 mounting screws from the instrument cluster trim plate and remove the trim plate. Remove the 4 mounting screws from the instrument panel face plate and remove the face plate.Remove the instrument light grid from the center of the cluster. From behind the instrument cluster reach behind the speedometer and disconnect the speedometer cable by releasing the tab. Pull the cluster forward just enough to detach the "check engine" light bulb from the center of the cluster. Remove the instrument cluster from the dashboard.

Posted on Jan 13, 2010

  • 3 Answers

SOURCE: Removing dash board on 2001

e emergency brake cable has to be removed at the pedal on the kick panel and not at the dash pay attention on removal and repeat steps to reinstall as it can be slid in from the front of the dash for new install but has to be removed in reverse steps

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Chevy S10 Blazer Serpentine Belt replacement


You use a breaker bar to move the tensioner, remove the belt and use the tensioner to put it back. You draw the belt and pulleys on a sheet of paper before removing, otherwise there should be a small diagram of the belt and pulley positions on the fan shroud or radiator support.

Jun 25, 2012 | Chevrolet S 10 Cars & Trucks

1 Answer

Removing dash board on 2001 Chevy Blazer to replace heater core. having problems with removing emergency brake cable.


e emergency brake cable has to be removed at the pedal on the kick panel and not at the dash pay attention on removal and repeat steps to reinstall as it can be slid in from the front of the dash for new install but has to be removed in reverse steps

Feb 27, 2011 | 2000 Chevrolet Blazer

1 Answer

Our 1993 chevy blazer's dome light won't shut off..had to drive home with it on...any suggestions


check the switch on the dash to make sure it is not turned 'on'-you should close the doors and check the switch to make certain that's all it is-if not,, spray the 'buttons' in the door, with a spray lubricant and push it in a lot-those buttons, when 'out' (extended) complete the circuit (ground) and they may be defective. Worst case scenario,, remove the light cover and, with a rag in your hand, remove the bulb so you can tackle it in daylight, when you have time.

Feb 03, 2011 | 1993 Chevrolet S-10 Blazer

1 Answer

I have a 1993 Chevy Blazer I recently purchased. The instrument panel only has certain items that light up. The speedometer is one of them. However, this too occasionally stops working. But if you bump the...


bad connection. unfortunatly the dash panel above the steering column will need to be removed to clean and replace any other blown bulbs. suggest if you do remove it, replace all the bulbs with new ones since you're there already.it's not a real complicated fix, mostly phillips screws holding it in, make sure you put emergency brake on because you will have to move the shifter into the lowest gear position to remove the panel. wipe the cluster panel down with a clean dry rag after you've done the replacement of bulbs to remove any oil that has come off your hands during the replacement. hope this helps and thank you for choosing fixya.com

Nov 21, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

Dash board is digital and the dash lights went out seeking information on how to remove the dash board console 1993 chevy blazer tahoe LT


Remove the 5 mounting screws from the instrument cluster trim plate and remove the trim plate. Remove the 4 mounting screws from the instrument panel face plate and remove the face plate.Remove the instrument light grid from the center of the cluster. From behind the instrument cluster reach behind the speedometer and disconnect the speedometer cable by releasing the tab. Pull the cluster forward just enough to detach the "check engine" light bulb from the center of the cluster. Remove the instrument cluster from the dashboard.

Jan 13, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

Have a 1998 full size chevy blazer and need to replace the heater core any help


you have to remove the whole dash board, airbags and all, I was quoted for over 2 grand, but got it done for 1300. good luck its a 17 hour job

Nov 21, 2009 | 1998 Chevrolet Blazer

1 Answer

How do i remove the dash of a 2001 chevy blazer to replace a heater core?


big job maybe you should buy a manual for that blazer, also label everything, the steering colum and every thing has to be removed before dash can be removed, good luck.

Oct 09, 2009 | 2001 Chevrolet Blazer

1 Answer

'01 Chevy Blazer transmission randomly switches from 2 to 4 wheel


Try this.My Blazer the same.Took the dash switch out, removed the back plate from the switch.Cleaned the four brass contact areas on the circuit board with a pencil eraser, then rubbing alcohol.Re-installed & works perfectly.

Sep 04, 2009 | 2001 Chevrolet Blazer

1 Answer

Replace the heater core in a 1993 chevy s-10 blazer


either the core has a hole or the fittings are not tied enough

Feb 09, 2009 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...