Question about 2010 Chrysler Sebring

Open Question

How to remove the seat belt adjuster on Chrysler PT Cruiser 1,6cc

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 958 Answers

SOURCE: Replacing Alternator For 2001 Chrysler PT Cruiser (Manual)

this instruction is general for all vehicles. i am sorry that i do not have particularly for your 2001 chrysler PT cruiser.

first, identify the alternator.
remove the fan belt on the alternator,
label and remove all wires that is attached to it.
remove all bolts that is holding it.
remove the old alternator.

do the reverse on installing it.

tnx 4 using fixya,

drcool

Posted on Aug 30, 2008

Ad
66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

rockitman187
  • 2559 Answers

SOURCE: 2004 chrysler pt cruiser starter motor removal

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

  • 290 Answers

SOURCE: chrysler pt cruiser fuel filter location?

Under vehicle, center, below seating area, mounted on top of fuel tank, in fuel pump module

Posted on Mar 27, 2009

localwonder
  • 6784 Answers

SOURCE: Change the thermostat on 2002 Chrysler PT Cruiser

Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.


* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.

NOTE
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.


9c06de2.jpg

Posted on Apr 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to check 2004 pt cruiser noise belt


use crc belt grip product
replace the hard /old belt
check for pulleys not spinning freely
check and adjust belt tension

Jan 05, 2016 | 2004 Chrysler PT Cruiser

1 Answer

How to remove the alternator


My search engine, Bing, found a picture of the PT setup which clearly shows the belt and adjuster layout. Type PT Cruiser alternator in the "images" section and see what pops up.

Aug 15, 2014 | 2003 Chrysler PT Cruiser

1 Answer

Remove recoil on driver side seat belt


remove b piller trim remove blots holding belt to body

Jan 22, 2014 | 2002 Chrysler PT Cruiser

1 Answer

Front seat removal pt cruiser


If you move the seats all the way back you should be able to get at the front two bolts on each seat. If you move the seats all the way forward you should be able to get at the rear two bolts on each seat. Once the bolts are removed unplug all the harness under the seats and remove the seats from the vehicle.

Mar 09, 2012 | 2002 Chrysler PT Cruiser

1 Answer

How do I change Serpentine belt on 2002 PT Cruiser


loosen the alternator adjustable screw until you can slip belt off ,always keep in mind how the belt goes back good luck

Mar 30, 2011 | 2002 Chrysler PT Cruiser

2 Answers

How to remove battery from PT cruiser


its under passenger seat 5 mins and its out ,,2 screws then the pannel at the front allows acsess

Jul 06, 2010 | 2001 Chrysler PT Cruiser

1 Answer

Driver seat belt on chrysler pt cruiser will not release from its bottom reel. This happened without warning


pop bottom cover off and check for debris caught around spool ,ratchet jammed or belt twisted these are the three most common problems

May 17, 2010 | 2002 Chrysler PT Cruiser

1 Answer

2002 pt cruiser belt replacement diagram


Asked under 2001 Category for a 2002 Question.

Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 2002 Chrysler PT Cruiser 2.4L DOHC In-Line 4-Cylinder Engine with the Engine Options (AC/No AC etc.). It also has Instructional and Directional Diagrams inorder to remove and/or replace the Belt(s).
Note: the differences between the Automatic Tensioner and those Tensioners with Adjusting/Locking Bolts/Nuts

http://www.2carpros.com/car_repair_information/year/2002/make/chrysler/model/pt_cruiser/2002_chrysler_pt_cruiser_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Mar 28, 2010 | 2001 Chrysler PT Cruiser

2 Answers

Describe your 2002 Chrysler PT Cruiser timing


Replace the belt at 100k with a new water pump pulley and tensioner. It would not be a bad idea while u r in there to replace the center motor mount. When the mount fails it is a pricey fix not a bad Idea to replace it since you have to remove it to do the belt.

Jul 04, 2009 | 2002 Chrysler PT Cruiser

1 Answer

Seat belts


You must replace the gas cartridges that tension the belts during a crash.

Oct 09, 2008 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2010 Chrysler Sebring Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...