Question about Cars & Trucks

1 Answer

My 97 eclipse died at 50 mph. 2.4 non turbo cranks over but no fire and the tach does not move when it cranks over

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 1,848 Answers

-Sounds like broken timing belt.


Mai

Posted on Oct 10, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dustyboner
  • 331 Answers

SOURCE: I have a 1995 mitsubishi

if you haven't checked the ASD relay, make sure its working.
175c874.jpg if thats okay, check the Cam Angle and Crank Angle sensors. if it isn't any of those, its probably the ECU

Posted on Jul 22, 2008

  • 1 Answer

SOURCE: crankshaft position sensor location

if u pull the battery and battery tray u can easily reach this

Posted on Nov 23, 2008

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

bunnydawg
  • 5158 Answers

SOURCE: how to change flywheel on 1990 300zx non turbo?

pull the transmission. remove the torque converter (automatics) or clutch and pressure plate (standards), the bolts for the flywheel are under that. make sure you replace the flywheel with the proper one especially if it's a standard.

Posted on Sep 02, 2009

Testimonial: "My car is a manual. Are the instructions the same? And can you be clearer and give me step by step what to do, please? Don't want any mistakes Thanx"

  • 122 Answers

SOURCE: how do you set the timing on a 420a 2.0 eclipse motor??

if you go to autozone.com you will gain access to the free manuals online for your vehicle. here you can get step by step instructions and cautions, in addition to torque specs for the head gasket. you will need to register and provide info about your car, it is FREE!!! Good Luck!

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 ECLIPSE JERKING AND POWER LOSS WHILE DRIVING


could be a number of things (throttle position sensor, crank position sensor, bad injector, faulty coil, bad plugs,etc) i would take it to a shop and have them scan it .If the scanner comes up with multiple problems and your forced to start "throwing parts " at it, remember most electrical parts cannot be returned once opened, so it could get expensive.shops sometimes have what i call "test pilots", properly working parts to put in to see if it corrects the problem through a process of elimination. this is one way a shop can actually save you money.

Apr 30, 2012 | 1997 Mitsubishi Eclipse

1 Answer

What is the firing order for a 97 eclispe spyder


1997 Mitsubishi Eclipse Spyder GS-T FWD 2.0 liter DOHC Turbo L4

a6519be.gif



1997 Mitsubishi Eclipse Spyder GS FWD 2.4 liter SOHC L4

97f1103.gif

Hope help with this (rememmber rated this).

Apr 12, 2010 | 1997 Mitsubishi Eclipse

1 Answer

Gas gauge light comes on, how much gas is left


i have a 97 eclipse and when my gas light comes on i have 10 to 20 miles until i run outa gas. depending on how you car runs and if it is turbo or not. on a non turbo 420a motor w/ a 5 speed i can do this.

Nov 24, 2009 | 1996 Mitsubishi Eclipse

2 Answers

What should the gap be for the plugs on a 97 Saab misfiring?


should be .9 to 1 in the saabs. thats what the manual says

Jun 10, 2009 | 1997 Saab 900

1 Answer

Motor swap


If your planing on swaping the 2.0 non-turbo(420a) to the 2.0 turbo(4g63t) your problem will be that the motor and transmission are on opposite side of one another. My GST has the trans on the passenger side and the motor on the driver. The 420a is just the opposite. If your serious about it you should get the motor rebuilt with higher performance crank, pistons, rods, exc.  And they make turbo kits for the 420a.  But you'll need better fuel delivery and some mild tuning.

Dec 23, 2008 | 1997 Mitsubishi Eclipse

2 Answers

I have a 1995 mitsubishi eclipse, 4 cylinder, 2.0 non-turbo. The car will crank but there is no spark and we are not getting any gas. We've checked all of the fuses and the relays. Do you have any...


if you haven't checked the ASD relay, make sure its working.
175c874.jpg if thats okay, check the Cam Angle and Crank Angle sensors. if it isn't any of those, its probably the ECU

Jul 22, 2008 | Mitsubishi Eclipse Cars & Trucks

2 Answers

Can i bplt up a eclipse 2.0L 420a non turbo to a 95 eagle talon non turbo


yes. they are exactly the same.

NOTE:
  • the 95-96 year models, have a few sensor plugs that are different than the 97-99 models. such as the coil pack and the cam angle senor.

Jul 21, 2008 | 1994 Eagle Talon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...