Question about Toyota Avalon

1 Answer

I have avalon 2009, i just removed the battery terminal n after a short time i putted it back, and after that my audio system is not working, there is a display of 'CANNOT READ PROGRAM PLEASE CONSULT TO THE DEALER' can anyone tell me what i have to do here?? do i need a to program my audio system or something alse?? im greatfull if any one can tel me the solution.

Posted by on

  • faari Dec 24, 2013

    sorry there was a fault about asking question, my radio, climate and other things are working but the navigation system. The only navigation system is not working. so do i need to program that with a new disc or can i do it without purchasing anything??

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 9,324 Answers

All the buttons have to be reset to the radio stations you had before. The clock will need to be set to the correct time too.

Posted on Dec 24, 2013

Testimonial: "sorry there was a fault about asking question, my radio, climate and other things are working but the navigation system. The only navigation system is not working. so do i need to program that with a new disc or can i do it without purchasing anything??"

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Nitrotrike
  • 589 Answers

SOURCE: keyless entry remote

Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks.

Posted on Jun 20, 2008

emissionwiz
  • 75235 Answers

SOURCE: programming a 1995 toyota avalon key fob

To program a remote... note that you must not delay more than 10 seconds between any of the operations.

Driver's door open, all other doors closed, key removed from the ignition switch.

Insert key into ignitions switch, then remove it.

Press LOCK then UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.

close and re-open drivers door.

Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times

Insert Key into ignition switch.

Switch ignition ON and OFF once to program a remote transmitter code while retaining the original codes or twice to program a remote transmitter code while erasing the original codes. three times to check how many remote transmitters are currently registered, or 5 times to erase all registered codes.

Remove Key from ignition switch.

System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. It will lock and unlock one to four times slowly, to indicate the number of remote transmitters registered if you chose option 3.

Press and hold remote transmitter LOCK and UNLOCK buttons at the same time.

Press LOCK remote button for 1 second: System should now lock and unlock vehicle once to confirm, twice to indicate registration has failed.

NOTE: to exit programming mode, close drivers door or insert key in the ignition.

NOTE: a maximum of 4 remote transmitters can be programmed

Posted on Oct 13, 2008

motor1258
  • 6674 Answers

SOURCE: how to reset security system on 2001 dodge durango

Try using key in doors to unlock them.

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is the fuel pump on a 2009 toyato avalon in the top of the gas tank ?


well it is in the tank and was put in through the top to replace the tank must be removed . so chceck all other options first like fuse /relay

Mar 11, 2015 | 2009 Toyota Avalon

1 Answer

Reset factory alarm on a toyota avalon xls 1996


If the alarm system has a battery remove it otherwise removing the car battery for a while may reset it. In emergency contact your local toyota dealers mechanics department and they may be able to help you at no cost.
If you put a general enquiry on google you might get lucky, do not be too specific. i.e. toyota 1994 alarm reset procedure

Sep 19, 2014 | 1996 Toyota Avalon

1 Answer

Battery warning light came on while driving then later went off. Voltage at battery was 13-14+ then only 12-13 when light went back on later.


Try taking the cables off the battery terminals and cleaning them with a battery brush. Then make sure they are tight when you put them back on. They may not have been tightened properly when the new battery was installed. If that doesn't work take the battery back to where you bought it and have them test it under load. It may be new but it may have one cell that is weak. If that checks good then I would start the car and remove the positive battery terminal. Use your multimeter from the ground to positive terminal to make sure the voltage regulator is putting out enough voltage.

Jan 28, 2014 | Chevrolet Blazer Cars & Trucks

1 Answer

Reset check engine light on 2000 avalon


stop the car and turn it off and don't forget to remove the key. the open the hood and find the battery. Then remove the negative battery terminal connector completely from the battery. with the battery disconnected turn on you headlamps as you would for night time driving. Wait an half an hour so all the current drains out the the electrical system. after the half hour TURN OFF THE HEADLAMPS BEFORE RECONNECTING THE BATTERY! Next reconnect the negative battery terminal connector back on the negative battery terminal don't forget to tighten it down. Put the key in the ignition turn the computer on to on BUT wait 5 seconds before actually starting the car, then start the car as normal and drive the car at least 25 miles 10 city 15 highway so the car can relearn all it functions again **Note first time start the car my be rough due that it need to relearn if it is acting rough apron start up let it idle for a bit before driving so it can calm down**

Oct 03, 2013 | Cars & Trucks

2 Answers

1998 Toyota Avalon XLS -- Will not start. No clicking.


It definitely sounds like a weak battery issue. Ck your connections at the battery for cleanliness & tightness. U need to have the batt checked along w the charging system & ckd for electrical shorts. If no problem is found that is the starting line. It may be a prob in the ignition system etc. if the problem isn't found by here. Good Luck

Mar 16, 2017 | 1999 Toyota Avalon

1 Answer

Hyundai audio system in acting weird?


What happened, you forgot to pay your radio bill? Now for the solution. I suspect you tend to turn on the headlights to see in the darkness. That may be the hint that will help find the problem! Try turning on your headlights at the times you say it works and see what happens. If the radio goes off, you have a short somewhere that shorts out the radio power!

Jan 11, 2013 | 2009 Hyundai Tucson

1 Answer

The audio system stopped functioning when I removed the battery terminal head but it is showing code on the display.


Hello,I am a Guru here on fixya and will answer your question.They do have codes that you have to reprogram back in to get them to work after disconectting the battery.Most of the time you have to take it to the dealer to get the code put in it.

Jan 31, 2011 | 2003 Honda Pilot

1 Answer

I have a 1995 Toyota Avalon XLS. Something keeps draining the battery!..the battery was new in July. If I take off the battery terminal when the car is not running..and then put it back on..the car...


So you have a parasitic power drain when the system is off. You can narrow the fault quite quickly if you have access to an ammeter (multimeter set to DC current). connect the ammeter in series between the battery negative terminal and its cable. Note the power consumption when everything is off. Remove and return each fuse in turn and each time note the current change. Check them all just to be thorough. There will be one circuit fuse that will be responsible for the majority of the current draw. It is this circuit that needs to be examined for a short or maybe a light being left on (glove compartment and trunk courtesy lights are the usual culprits). It maybe that you cannot spare the time immediately to resolve the issue so in the mean time leave this fuse out and reconnect the battery, which should now hold its charge. Good luck

Dec 29, 2010 | 1995 Toyota Avalon

1 Answer

1999 toyota avalon, starter location, or engine view diagram


it's under the battery. see instructions below for removing.

REMOVAL & INSTALLATION

  1. Disconnect the cable from the negative terminal of the battery.
  1. On some early models with cruise control, you may have to remove the battery.

    Also on some models with cruise control, remove the actuator cover and disconnect the wiring harness. Remove the three bolts and then lift out the cruise control actuator. Remove the bracket from beneath the actuator and put aside.
  1. Peel the rubber boot away and remove the nut and disconnect the negative battery cable from the magnetic switch terminal on the starter. Disconnect the electrical connector also located on the magnetic switch.

1f54e61.gif Fig. Remove the these two starter mounting bolts . . .
  1. Support the starter by hand and remove the two mounting bolts.
  1. Remove the starter from the transaxle.

Oct 04, 2010 | Toyota Avalon Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...