Question about 2000 Hyundai Elantra

1 Answer

Window regulator hot to fit cable on window regulator

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Window regulators are not repaired... they are replaced.

Posted on Jun 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2009 HHR.. The rear passenger window went down the other day but stuttered to do so...


you need to get a new window regulator,,,
the inside the regulator the cable came out of the
plastic wheels.
or the bolts holding the regulator broken
your window motor it work fine....

May 29, 2015 | 2009 Chevrolet HHR

1 Answer

Can I change the electric window to a manual window on a 2004 Chevy Express


it appears that the drive control for the regulator packed it in ( stripped gears or broken cable)
The pressing and holes should be in the door under the trim and the regulator mounting points should be the same . You may have to change the door trim to fit the handle for the regulator.

Dec 27, 2014 | Cars & Trucks

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

2 Answers

Window regulator cable broke???


Here's a video that will show you how to replace the rear window regulator in that car.
">

Apr 03, 2010 | 2001 Chevrolet Impala

2 Answers

2000 beetle ecectric window went down will not come up motor works


Personally, I'd leave this one to the experts...go to a friendly local body shop and have them look at it ($50+ parts)
Good Luck

Jun 25, 2009 | 2000 Volkswagen Beetle

1 Answer

Trying to figure out how to rewind the cable correctly on the right rear window regulator,I seem to have just one more time around the regulator cable pulley,but i cant figure out how to get it to track...


Those regulators are not designed to be repaired -- only replaced. The cable spool, pullys and cable are installed as complete components -- the slack is taken out of the cable during assemby at the manufacturer.

Jun 10, 2009 | Hyundai Motor 2004 Accent

1 Answer

98 VW Window Regulator


Do you have the metal assebly completely in front of you? And you've made sure all the cables are passed the same. If yes there should be an arrow type area on each pulley? Also each pulley should have a smaller and a larger area?

Oct 10, 2008 | 1998 Volkswagen Beetle

Not finding what you are looking for?
2000 Hyundai Elantra Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...