Question about 2001 Ford Taurus

Open Question

Engine code p1309

How do you time a camshaft position synchronizer on a 2001 ford taurus with a 3.0 v6 engine.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: where is the camshaft position

if u look on the drivers side of the top of the engine the cam sensor is in the block where the distrutor used to go, here is a picture of it4fd7155.jpg

Posted on Sep 08, 2010

Ad
warlock61
  • 659 Answers

SOURCE: how to synchronize a 2002 ford taurus 3.0 single cam

was the synchronizer ever replaced? It might only need the sensor. there is a special tool needed to align synchro correctly

Posted on Nov 25, 2008

warlock61
  • 659 Answers

SOURCE: need a diagram of the serpentine belt for a 2001 ford taurus

3.0L 2V


8263e1e.gif

Posted on Nov 25, 2008

blueextc3221
  • 15935 Answers

SOURCE: need diagram of serpentine belt for 94Solution for "need diagram for replacing serpentine belt for 94 ford taurus gl w/3 0 v6 engine and a/c" ford taurus gl w/3.0 v6 engine and a/c

89beac5.gif Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 21, 2009

  • 85 Answers

SOURCE: Where is the camshaft position sensor on a 2000 Ford Explorer?

in the rear like where the dist would normaly be

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have 1997 Ford explorer 5.0 Replacing camshaft synchronizer It's stuck


Help . Camshaft Sensor - Omfg ( Pics ) - Ford Explorer and Ranger ...

www.explorerforum.com > ... > Stock 1995 - 2001 Explorers
Oct 20, 2010 - 19 posts - ‎7 authors 98 Ford Explorer 2wd 5.0L .... If you're replacing the entire camshaft synchronizer, it gets a little more complicated. ... i would like to only be able to replace the sensor, but if its gonna get ... 1997 xlt v8 awd + 00,XLS .... taking care that the entire shaft comes out of the hole and isn't stuck to the oil pump shaft. Stuck cam position sensor shaft?
2 posts
Nov 24, 2013
Idler pulley squeaking
6 posts
Nov 16, 2012
Easy Camshaft Synchronizer Replacement
8 posts
Sep 11, 2012
Help Diagnose my intermittant Missing Problem
19 posts
May 23, 2004
More results from www.explorerforum.com

Replacing Camshaft Synchronizer & Sensor - Ford Mustang Forum

www.allfordmustangs.com > ... > V6 TecCamshaft Position Synchronizer Replacement - YouTube? 1:16https://www.youtube.com/watch?v=fXOJXnYIZQkNov 18, 2009 - Uploaded by 2003FordTaurus2003 Ford Taurus 3.0L Vulcan 181K miles with chirping sound ... does the shaft move out of its place when ...Camshaft Sensor/Synchronizer Replacement - Page 5 - Ford Tru

Nov 29, 2015 | Ford Cars & Trucks

1 Answer

What is a code p1309 on a 2001 mercury sable 3.0 and how do you fix it?


It is indicating a defective Camshaft Positioning Sensor...
8f3ba6d3-0e4f-4666-9d9f-51691d01e229.gif


457a25a3-9c9e-4e47-a21b-62f188a5c29c.jpgCost = $35

saailer

Oct 02, 2013 | 2003 Ford Taurus

1 Answer

P1309 misfire code


Could be that the camshaft position sensor could be defective, or the camshaft synchronizer (the part that took the place of the distributor on DIS engines) is failing, or if you have recently had the camshaft synchronizer replaced it could be out of time....

May 23, 2013 | 2001 Ford Taurus

1 Answer

Showing Code P1309. Replaced the cam sensor and still showing the code or CMP. What can it be?


You may need to replace the PCM, engine computer. very rare issue. Personally, I would leave it. It is only there to tell you if a cylinder is not firing. You will know if one is.

HD41 CHECK CMP SENSOR OUTPUT
  • Connect PCM.
  • Connect digital multimeter.
  • Start engine and vary engine RPM.
  • Measure voltage between CMP and PWR GND circuits at the PCM harness connector.
Does AC voltage vary greater than 0.1 volt AC? Yes No VERIFY the correct installation by referring to the Electronic Engine Controls, Section 303-14 in the Workshop Manual. If CMP is installed properly, REPLACE PCM (refer to Section 2 , Flash EEPROM). REPLACE CMP sensor. COMPLETE Misfire Monitor Repair Verification Drive Cycle.

----------------------------------------------------------------------------------------------
P1309 - Misfire Monitor Disabled When the misfire monitor is disabled, usually due to the input signal generated by the camshaft position (CMP) sensor, by sensing the passage of teeth from the CMP wheel.
  • Camshaft position sensor
  • Powertrain control module
  • ECT, MAF, and CKP sensors
Verify the CMP is installed correctly and not out of synchronization.

Aug 05, 2011 | 1999 Ford Windstar

1 Answer

Replaced motor 01 taurus 3.0 run great but kicked up p1309 after attempting to correct misses real bad got #1 up and used tool to install but dont know if maybe 180 out or other problem replaced sensor but...


does your scanner that read the engine code give you any live data? if so look at the fuel trims, if it shows positive fuel trims on one bank and negative fuel trims on the other then your synchronizer is 180 out ouf time.

Jul 28, 2011 | 2001 Ford Taurus

1 Answer

2001 ford mustang 3.8 v6 p1309 code . what could be the problem?


P1309--Misfire Monitor Disabled

When the misfire monitor is disabled,usually due to the input signal generated
by the camshaft position sensor

Possible Cause---

Cam Position Sensor
Powertrain Control Module
ETC,MAF,CKP

Verify CMP is installed correctly


You need a local repair shop to check it out

Nov 10, 2010 | 1999 Ford Taurus

1 Answer

Engine code p1309 P/S advice on repair


The definition of this code is:
P1309 Engine Misfire Detection Monitor not enabled

It's a problem with the detection circuitry, not a detection of a engine misfire condition. I found this quickly on the net:
Diagnostic Trouble Code (DTC) P1309 indicates Misfire Detection Monitor is not enabled.

Breakout box installed, PCM disconnected. Connect digital multimeter between PCM test pin 85 and test pins 51 or 103. Bump engine in short burst with the starter without starting engine for at least 10 engine revolutions. Answer this question: Does digital multimeter reading switch between low (less than 2.0 volts DC) and high (greater than 8.0 volts DC)?

If Yes, Verify correct installation by referring to the Powertrain/Engine Group in the Workshop Manual. If the CMP is installed properly, REPLACE PCM. RESTORE vehicle. RERUN Quick Test.

If no, REPLACE CMP sensor. RESTORE vehicle. COMPLETE Misfire Monitor Repair Verification Drive Cycle. RERUN Quick Test.

The CMP sensor is the Camshaft Position Sensor.

Nov 08, 2010 | 2000 Ford Taurus

1 Answer

My car have problen code P1309 plz help me


HI, The P1309 can be set due to a couple of problems the common being the CPS camshaft position sensor failed. There are other components that can cause this code to set including the ECT engine coolant temp, MAF mass air flow, CKP crank shaft position.There are no simple test that can be done at home but this code is usualy quick to diagnose for a good tech.

Aug 26, 2010 | 2001 Ford Taurus

2 Answers

Engine light on with code P1309


This code could mean:
  • the camshaft position sensor could be defective,
  • the camshaft synchronizer (the part that took the place of the distributor on DIS engines) has failed,
  • if you have recently had the camshaft synchronizer replaced it could be out of time.

Aug 17, 2010 | 2001 Ford Taurus

1 Answer

Check engine light on. has dtc of p1309. what could it be? I replaced cam sensor but code is still there.


Code PO1309 : Misfire Monitor Failure Description : When the misfire monitor is disabled,usually due to the input signal generated by the camshaft position sensor, by sensing the passage of teeth from the camshaft position wheel. Possible Causes : PCM(power train control module), Mass Air Flow Sensor, Engine Coolant Temperature Sensor, Crank Shaft Position Sensor, Camshaft Position Sensor.

Jan 08, 2010 | 2001 Ford Taurus

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

508 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...