Question about 1984 Ford Bronco

1 Answer

Need to know how to pull out ignition switch for a 1984 ford bronco

Posted by on

  • yadayada
    yadayada May 11, 2010

    do u mean the lock cylinder or the actual electrical switch at the base of the steering column?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Ford Master
  • 3,854 Answers

If you can insert the key and turn it to the run position. Then look under the steering column where the key is you will see a hole in the plastic cover if you push the pin inside with a paper clip or pick of some sort then you should be able to pull the switch out. 
If you cant get to the pin then pull the lower cover from around the steering column where the switch is located it should have only (3) phillips screws holding it. 
Sorry if you get confused about the plastic cover around the steering wheel, can't remember if the 84's had that. But regardless on the underside of where the ignition switch is where you will find the pin hole.
Good luck and hope this helps.

Posted on Apr 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace ignition switch/tumbler on a 1995 Ford Bronco


Do you still have the ignition key and will the ignition key cylinder switch turn? If so, you turn the key to Run, press the button on the bottom of the steering column that's accessible once the shroud is removed, then pull the key and cylinder switch out of the column.

If you no longer have a working key, then things get a bit more tricky.

I don't recall what year Ford started using the PATS system, but if your 1995 has PATS you'll need to have the PATS module reprogrammed to the new key before the car will start.

-Rod

May 01, 2017 | 1995 Ford Bronco

1 Answer

How do I remove an armrest on a 1984 Ford Bronco?


Pull the armrest vertically up. There is a slot in the armrest and a pin on the frame. You have to match these to pull the armrest off. Without a zipper it's a little more challenging. Some armrest have a little screw that keeps the armrest on the frame. The older models usually worked with the slot and pin.

Dec 31, 2016 | 1984 Ford Bronco

1 Answer

How to fix the timing on the distributor in a 1984 bronco 2?


I doubt its the timing.
What you describe sounds more like a lack of fuel problem.
Fuel pressure, throttle position sensor, or something else.
To actually check the timing you put the ignition in test mode and use a timing light on #1 cylinder.

Jul 24, 2012 | 1984 Ford Bronco II

1 Answer

Starter engages and will not stop untill battery cable is pulled new starter new ignition new stater solinoid


either the bendix is locking to the flywheel , or there is a short in the wiring to the starter somewhere!

Mar 08, 2011 | 1984 Ford Bronco II

1 Answer

1984 bronco II dies when going up hill


If the vehicle dies going up hill it may need a tune-up or check transmission fluid level to make sure the appropriate levels are set. Sometimes when level is low it creates a hard pull on the transmission when going up hills.

Nov 28, 2010 | 1984 Ford Bronco II

1 Answer

No power,no dash lights,no power to fuse box or ignition switch


Check your fusible links. There will be one main one at the starter relay. You'll find it bolted to the fender nearest your battery (passenger side). One link controls the majority of the power in the bronco. A word of caution though... If you replace it and your new link blows again, you have a short somewhere that you'll have to track down.

Apr 08, 2010 | 1984 Ford Bronco

4 Answers

What is the firing order for a 1984 ford bronco 2


1-4-2-5-3-6
Now you need to know which cylinder is which. If you stand at the front of the truck looking at the engine, the number 1 cylinder is on the left closest to you. The left bank has cylinders 1-3-5 and the right bank has 2-4-6. So number 1 is at the left front and number 6 is at the right rear.

Jan 25, 2010 | 1984 Ford Bronco II

2 Answers

My 1984 Bronco's fan switch will only work on high. The switch is good. A/C has been disconnected from truck. How can I fix it?


Your blower motor resistor is bad. Replace this and it should fix your problem. Hope that helps.

Dec 31, 2009 | 1983 Ford Bronco

1 Answer

1984 bronco quit 4 days after ignition system was replaced


fuel pump i had the same problem good luck

May 30, 2009 | 1984 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...