Question about 1998 Toyota Camry

1 Answer

Seat belts are not working

The passenger and the drivers side seat belts are not working.
The passenger side is very tight, can not pull it out.
The driver side is all the way out can not go back in.

Thank you,

Ramiro L.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Driver side has a broken clock spring, you will have to replace the whole retractor because you can not just replace the spring. Nick

Posted on Apr 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My renault clio 3 was in an accident and now the seat belt are pulled tight, is there any way I can fix this without replacing the belts


after a seat belt being stressed that much in any accident it locks out

almost every 3rd world country would say the seat belt should be replaced with a new one

if its you or passengers wearing that one .. ..
better idea to have reliable safety belts
than a head going through a windshield

Oct 10, 2016 | 2007 Renault Clio 3

1 Answer

The rear drivers side passenger seat in my Mercedes 2004 ml350 is stuck down...how do get it to come back up. very little room to work


Not an easy task. You likely have one of 2 problems. If center seat belt is in the seat that is down, it may be locked. If so, you need to remove the seat back cover then the seat belt retractor. You can then position the seat belt retractor upright (how it sits when the seat is up) and pull the seat belt out making slack to raise the seat. This only happens if the either the stop on the seat belt is broken or the seat belt guide on the seat back is broken. If that's not the problem, you likely have a release cable that has come loose under the seat. If you look at the half that works, you can determine what you need to move on the locked seat and try to get to it with a long tin screwdriver or similar implement.

Mar 01, 2015 | 2004 Mercedes-Benz ML 350

1 Answer

2011 subaru forester front passenger seat belt is locked too tightly and will not release, how do I fix?


The reason is the belt mechanism is damaged and the belt needs to be replaced. What happens is the gears lock this usually only happens when the vehicle is in a collision or has a major and hard stop

Mar 29, 2017 | Subaru Cars & Trucks

1 Answer

Air bag code 33 for a 2005 lincoln town car


2005 Towncar SRS Code 33 (3 flash + 3 flash, repeat this set for twice. then Beep 5 times pause x 5 = 25 beeps every 30min).

This means you have problem with left (Driver) side pretentioner (Seat belt retract system).
It doesn't mean physical belt or retract mechanism.It is just bomb wiring which is part of airbag system.
When airbag deploy, passenger must stay tight in seat otherwise body lean to front then slam back to seat by airbag.
if belt is loose or delay to lock, passenger's body rocks back and forth.So, system use small bomb (Fire power) to lock and retract seat belt when airbag deploy.There is small bomb and igniter in part of Seat belt retractor.
Code 33 is warning for this part on 2005 Towncar.(older model is different meaning in Ford/Lincoln, it's possibly passenger side airbag system for earlier model)
Before you work for any part of Airbag system and touch any "Yellow connector", * *Disconnect battery (negative side is good enough) and wait at least 5 min to clear all power in system**.(Airbag store back up power for few minutes to be able to deploy even in case if power disconnected)
by the way, you should move your driver seat most forwarded position before you disconnect battery to make it easy to work with seat belt.
locate driver side seat belt retractor (in center pillar between front and rear door, you may have to fight with weather strip)

Locate Yellow connector on bottom of Seat belt retractor (it's called "Pretensioner")it is located on very bottom of rear side of retractor.
only one yellow connector. (make sure your battery is disconnected)
Check its physical connection or looseness.if connection looks fine, you may have to replace whole seat belt ($180-$200 in Lincoln dealer)
You can check if pretensionor is good or bad by regular tester, but unless you know how, I won't tell (because I don't wan't you to blow out pretentionor).








Jul 19, 2012 | 2005 Lincoln Town Car

1 Answer

Mercedes clk 320 airbag


If the airbag light is on something in the system is broken. Go to AutoZone or similar and have them scan the airbag system for codes. My guess would be a faulty seat sensor or a faulty seat belt sensor

Jun 16, 2017 | 1999 Mercedes-Benz CLK

1 Answer

Remove rear seat lexus es300 2008


the bottom of the rear seat pulls straight up at the front and out. its pretty tight, you need to pull very firmly.

Oct 19, 2009 | 2003 Lexus ES 300

1 Answer

The right passenger seat belt will not pull out. It seems to be stuck in the "housing "for the belt on the side floor of the vehicle


Take off cover and check it out. Worst case New Seat Belt Assy and you will need the special torx type driver socket just for seat belts to remove it

Sep 26, 2009 | 1998 Buick Park Avenue

1 Answer

How do we fix front passenger side seat belt retractor on 1999 Ford Taurus? It will not pull out....


you may have to remove the bolt that holds the buckle to the floor. Try to push the belt into the retractor and see if it frees up.

I assume you are saying it is in the locked mode. It has an automatic lock mode for holding a child seat. When the belt is pulled all the way out, it goes into locking mode. You will hear it ratchet when the belt starts going back in.



Section 01-20A: Restraints, Active 1999 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Safety Belt, Lap/Shoulder The dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front seat passenger and rear seat outboard passengers operates in two ways:
  1. In the vehicle sensitive (emergency locking) mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 8 km/h (5 mph) or more. The front and rear outboard seat belt retractors can also be made to lock by pulling/jerking on the belt.
  1. In the automatic locking mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled and does not allow the occupant freedom of movement. This mode provides tight lap/shoulder belt fit on the occupant and on a child safety seat or infant carrier installation restraint.
  1. When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode.
sxh~us~en~file=ani_caut.gif~gen~ref.gif WARNING: REAR-FACING INFANT SEATS SHOULD NEVER BE PLACED IN THE FRONT SEATS.
The automatic locking mode must be used when installing a child safety seat on the front passenger seat and rear outboard seats where dual locking retractors are provided

Apr 21, 2009 | 1999 Ford Taurus

2 Answers

1999 Dodge 2500 passenger side seat belt wont release


so after completely tearing the seat apart I found 2 wires going up to the seat belt mechanism from under the seat, these wires got caught in the seat mechanism underneath and were shredded. There must be a small solenoid inside the seat belt mechanism because I could hear it click after I repaired the wires(this circuit is live even with the ignition off) Im not sure how it all works but this solved my problem.

May 21, 2008 | 1999 Dodge Ram 2500 4WD

2 Answers

Electric retractable seat belt problem


check your fuses. there is also a lever next to te parking brake..make sure it's down

May 17, 2008 | 1988 Toyota Camry

Not finding what you are looking for?
1998 Toyota Camry Logo

441 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...