Question about Plymouth Voyager

2 Answers

Get to the back plugs - Voyager Plymouth Cars & Trucks

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 23 Answers

Changing the rear plugs on 3.0, 3.3, and 3.8 liters requires that the front end be up on car ramps and rear tires chocked, several gallons of patience and long arms.
The 2 plugs closest to the drivers side require a 5/8" sparkplug socket with 3/8" drive (with needlenose pliers remove the rubber grommet from inside of socket), a 3" extension 3/8" drive and a 3/8" ratchet.
The plug on the passenger side requires the same 5/8" sparkplug socket, to which you will connect a 1-1/2" extension 3/8" (hard to find but available), connected to a 3/8" universal joint, then all pieces wrapped with electrical tape so you don't lose any pieces and for rigidity) and of course a 3/8" ratchet. All this will allow you to just sneak in past the power steering bracket to get to the plug.

NOTE: If the spark plug will not break loose...Stop. Get some penetrant on those plugs and let work for a bit (hour) then try again.
NOTE: Carefull not to angle the socket on sparkplug when tightening lest you crack the porcelin top off.

Posted on Apr 22, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

3.3 liter you have to get them from under the van lifted up on a rack!

Posted on Apr 22, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Interior fuse box. There are 3 fuse slots that are not id'd with no fuse in place. What do they go to?

there is no need to go any where near the fuse box
trailer shops and tow bar fitting shops sell a piggy back harness where you pull the plug of the back of a tail light and the piggy back connect plugs in with the car harness plugging into the back of that piggy back plug
run the wires out to the trailer connection and connect as per the wiring numbers instruction
quick easy and for most part fool proof

Nov 14, 2015 | 2004 Nissan XTerra

1 Answer

Code p0302 did plugs and wires still comes back

Move the coil to plug 3 and plug 3 coil to plug 2. That will prove faulty coil pack.

Nov 18, 2017 | 2002 Hyundai Elantra GLS

1 Answer

How to remove the spark plugs on a 99 mazda millenia

Make sure car is cold. Use socket wrench and spark plug socket to remove old plugs. Add new plugs, and then put wires back.------------------------------------------------------------------------------------
Multi-Di@g Access

Jan 14, 2013 | 1999 Mazda Millenia

1 Answer

Removal of back spark plugs on 2003 buick rendevouzs

if this has the 3.8 or similar, go under alternator to access the back left plug, then work from top of engine and remove whats necessary to get to other 2 plugs. use a spark plug socket and 3/8 ratchet to remove the plugs. and universal if need be. good-day !

Mar 22, 2012 | 2003 Buick Rendezvous

1 Answer

Plug turned a 1/4 turn and locked down didnt want to force it

no dont force spark plug its trying to cross thread.back spark plug back out.apply thin coat of anti seize compound to spark plug threads.if you have problems getting spark plugs back in a hard to reach place, use a long piece 3/8 vacuum hose about what ever length you vacuum hose over spark plug insulator then install spark plugs to hard reach places to keep from cross threading.if plug tighten 1/4 turn.back out spark plug and try again.dont cross thread or you have to remove cylinder head.if spark plug hole hard to reach to retap or install thread inserts.

Apr 09, 2011 | Toyota Pickup Cars & Trucks

1 Answer

Where are the plugs located on the transmission and, what mm size wrench will I need to remove them.

spark plugs you mean there not on trans mission there on engine under plug wires first make sure car is off pull all wires off take your spark plug socket and take plugs out when done slap wires back on there and your good to go when you pull wires off plugs soak in soapy water before putting back on it makes it easyier for them to go back on that way try not to mix them up they have a certain way get correct fireing order let plug wires completely dry

Dec 09, 2010 | 1996 Honda Passport

1 Answer

I replaced my spark plug wires on my 1996 chevy truck. may have crossed one,need a diagram from the spark plugs to the distributer cap.

Since you didn't state whether it is a V6 or V8, I'll give you both.

V6 -4.3Liter
Firing Order is 1-6-5-4-3-2
Distributor rotor turns Clockwise
Number 1 spark plug tower on distributor cap, faces the front of the engine.

->Drivers side, spark plug order in engine, starting from the Front going back:
->Passenger side, spark plug order in engine,
starting from the Front going back:

If it's Electronic, the distributor cap has a Left side, (Drivers side), and a Right side, (Passenger side)
Starting from the Front, going back on the Left side,
Starting from the Front going back on the Right side,

V8-5.0, 5.7, and 7.4Liter
Firing Order is 1-8-4-3-6-5-7-2
Distributor rotor turns Clockwise
Number 1 spark plug tower on distributor cap,
faces Front, towards the Drivers side.

Electronic distributor cap has two sides. Drivers, (Left), side and Passenger, (Right), side.
Starting from Front going back on Drivers side,
Starting from Front going back on Passenger side,

Spark plug order in engine, starting from Front going back, Drivers side:
Spark plug order in engine, starting from Front going back, Passenger side:

Aug 28, 2009 | 1996 Chevrolet K1500

2 Answers

Cannot find but 4 spark plugs in 1998 Cadillac sts

4 plugs in the front 4 in the back it is necessary toi remove some components to gain access to the rear bank of plugs

Jun 07, 2009 | 2001 Cadillac Sts

2 Answers


Very easy process but takes a little time. Remove plastic cover on top of engine to uncover wires going back to ignition coils. Remove plug wire and trace back to coil. Remove and replace spark plugs on at a time, same with wires. Spark plugs need .5 gap. good luck

Apr 25, 2009 | 1997 Oldsmobile Aurora

1 Answer

Alternator Replacement Procedures

disconnect the battter cable.
find your tensinor and release the belt,
unplug the plug from the back of the alternator,
take the nut off the back and remove the second wire,
take off the 2 bolts that hold on the alternator,

now install the new one.
put the bolts back in,
plug the plug back in and connect the wire,
put the belt back on,
reconnect the battery.

Aug 07, 2008 | Ford Contour Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides