Question about 1998 Ford Mustang

3 Answers

Engine temperature sensor located on a 1998 Ford Mustang GT

Where is the engine temperature sensor located on a 1998 Ford Mustang GT?

Posted by on

  • 2 more comments 
  • chrisp952 Apr 22, 2009

    It is for the gauge

  • chrisp952 Apr 22, 2009

    I received your response, thank you. But there is no picture showing up in my browser. I am new so maybe I am missing something?

  • chrisp952 Apr 23, 2009

    I have tried a couple  of different browsers. Show  the picture as a broken link.  When I click  on them I get "page not found" error.
    Here is  the  link I get: http://www.fixya.com/uploads/images/9EED...  
    When I try it  in several browsers I always get page not found.

  • yadayada
    yadayada May 11, 2010

    for the gauge or the fuel injection?

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 31 Answers

Left hand side (if facing it), behind distributor, above oil fill.

Posted on Apr 22, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 2 Answers

I got a 2002 gt mustang with a 4.6... when I switch from 1st to 2nd it's good. 3rd gear I hear a winding noise. Sounds like its coming from the driveshaft to the rear end. The fluid levels are good in the rear end and when my car is in neutral, and I give it gas, it don't make that high pitch noise. Is the rear end going out?

Posted on Jul 29, 2013

  • jason Jul 29, 2013

    I got a 2002 gt mustang with a 4.6... when I switch from 1st to 2nd it's good. 3rd gear I hear a winding noise. Sounds like its coming from the driveshaft to the rear end. The fluid levels are good in the rear end and when my car is in neutral, and I give it gas, it don't make that high pitch noise. Is the rear end going out?

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,066 Answers

Here is a pictureengine temperature sensor located on a 1998 Ford M - 79c36d2.jpg

Posted on Apr 22, 2009

  • yadayada
    yadayada Apr 22, 2009

    here it is

  • yadayada
    yadayada Apr 22, 2009

    I show the pictures here on my end?? do u have some kind of security block?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fog lamp relay located on 98 gt mustang


It's in the engine compartment fuse block. A LT BLU/BLK wire is connected to it

Oct 06, 2012 | 1998 Ford Mustang

1 Answer

98 mustang gt O2 Scensor location


Hi, the O2 sensors are located on your exhaust mid-pipe all the way forward near where it attaches to your headers. If you have a factory catalytic h-pipe, they are located forward of the two forward-most cats. I have a Magnaflow catalytic x-pipe on my daily driver, so I only have two cats and the O2 sensors are super easy to get to.

Jul 22, 2011 | 1998 Ford Mustang

1 Answer

I had my O-2 sensor replaced about 2 yrs. ago on my 1998 Ford Mustang GT, 4.6 liter several years ago. My check engine light came on a month ago and the Dealer told me it was the O-2 sensor. Do I have...


Hi,

$500 is a bit high. The sensors are on the exhaust and basically they help your car exhale. If you continue driving on a bad one it will throw your exhaust, intake and finally engine off key...

They cost about $90 buck a piece if you dont shop around and you can ask a tech savvy neighbor to put them in for you. The website below should be of help.

http://www.autopartswarehouse.com/mmp/ford~mustang~oxygen_sensor~parts.html

Good driving.

G

Feb 10, 2011 | 1998 Ford Mustang

1 Answer

My coolin fan for my engine wont run? how do i fix it? 98 ford mustang gt


okay heres what causes not to kick in,
1 a bad motor
2 bad tempeture sensor
3 bad/defected fuse or relay.
check the fuses and your fan relay first. swap them around to test is every thing well then test the motor dirtectly, if its fine and works, then tempeture sensor on the engine. remove the harness and put a jumper wire on the prongs and what it kick the fan in. have the ign on with engine off for this. if it works replace the sensor.
hope this help you.

send mr your comments thansk

Aug 02, 2010 | 1998 Ford Mustang

1 Answer

I am installing a chip and cant located the IAT in my 2009 ford mustang. please help. if it was located somewhere else please describe in full where that is located too thanks!


INTAKE AIR TEMPERATURE SENSOR (IAT) is normally located at the engine air filter housing for old models but i think yours its incorporated with the mass air flow unit (assembly). Thats the sensor after the air filter

Feb 01, 2010 | 2008 Ford Mustang

1 Answer

Engine light stays on my 1998 mustang GT 4.6 Lt.


i don't see a code in your question. be that as it may if you are in the states you can go to an autozone and they will scan the codes for free

Sep 06, 2009 | 1998 Ford Mustang

1 Answer

Im putting in the boss performance module


please rate as problem solved if this is what you need.



Section 03-14: Engine Controls, Electronic 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Intake Air Temperature (IAT) Sensor Removal and Installation
  1. Disconnect battery ground cable (14301) .
  1. Disconnect engine control sensor wiring (12A581) from intake air temperature sensor (IAT sensor) (12A697) .
  1. Remove intake air temperature sensor from air cleaner outlet tube (9B659). (This is the tube that goes from the air cleaner to the engine.)
  1. To install, reverse Removal procedure. Tighten intake air temperature sensor securely.
--------------------------------------------------------------------------

Jun 02, 2009 | 1994 Ford Mustang

1 Answer

It is a 2001 Mustang GT 4.6 litre Manual transmission. I need the locations of my Power Train Control Module and my Engine Coolant Temp Sensor.


ECT is located to the right(passenger side) of the alternator in the intake manifold.
PCM is located behind the right(passenger) kick panel under the corner of the dash.

Mar 20, 2009 | 2001 Ford Mustang

4 Answers

2005 mustang gt


replaced fuel filter yet ? have you checked fuel pressure and the fuel regulator

Sep 03, 2008 | 2005 Ford Mustang

Not finding what you are looking for?
1998 Ford Mustang Logo

736 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...