Question about 1994 Ford Bronco

2 Answers

Hi how do i take of the front rotor for a 94 ford bronco?

Posted by on

  • lanning08 May 11, 2010

    there is no bolt in the middle



×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 29 Answers

After you remove the tire and caliper youneed to remove the hub assembly.

Here is a writeup on removing 5-bolt auto hubs
http://danielphotography.us/bronco/manualhubs/
Here is a writeup on removing 3-bolt auto hubs
http://www.superford.org/vehicles/re...d=3749&s=14884
Here is a writeup on removing manual hubs
http://fullsizebronco.com/forum/showthread.php?t=5450

then you need to either buy rotor with hub housing or separate the two. to separate the hub and rotor you hammer out the studs, then you can hammer the rotor off the hub assuming the rotor is bad seeing this will ruin the rotor

Posted on Nov 28, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 398 Answers

Have you got the wheel off, this is first step. next take off the pads and caliper. you dont have to disconnect the brake line. next there is a cotterpin and bolt holding the rotor on( in the center under a cap w grease in it), remove these and it should come off. if its rusted on youll have to hammer it a bit.

Posted on Apr 22, 2009

  • josh1111 Apr 22, 2009

    dont hit the rotor on the back if it is rusted hit it on the tops and sides of the part were the studs are on.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change front four wheel drive rotors on my bronco?


Lift it up, remove the tire, remove the caliper and caliper mount bracket (2 separate pieces) then knock the rotor off, you can smack it with a hammer but if you're reusing the rotors and are just turning them dont hit them where the pads grab

Feb 07, 2012 | 1990 Ford Bronco

1 Answer

Remove the rotors on 1990 FORD BRONCO? Got the


Here is a website that a free manual can be down loaded for your vehicle


http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

May 01, 2010 | 1990 Ford Bronco

1 Answer

How do you tighten steering on 94 bronco


Hi:
Loose steering is caused by worn parts. You need to check for slop in the tie rod ends first, as they are a common wear item, and the rest of the steering linkage next. You can watch under the front of your bronco, as someone else slowly moves the steering wheel. if you see movement in a connecting joint before the tire moves, then that is a suspect. Also check out your front tires too. look for abnormal wear, to indicate a problem.
Hope you tighten things up!

Apr 29, 2010 | 1994 Ford Bronco

1 Answer

Is there somewhere I can find a diagram to remove the harmonic balancer on a 94 ford bronco


you can try autozones website, all you have to do is remove the belts, remove the fan and fan shroud,then remove pulley in front of balancer, then remove center bolt holding balancer, now use a puller to remove balancer, hats all good luck.

Nov 07, 2009 | 1994 Ford Bronco

1 Answer

My four wheel drive in my 94 bronco will not work


Check to see if your front drive shaft is turning. If it is it's most likely the hubs.

Sep 11, 2009 | 1993 Ford Bronco

1 Answer

Help with rotors please


you have to knock out all the wheel studs first. these are pressed in, just hammer them out then you can hammer the rotor off by placing hub and rotor, outer side up on flat surface. this will probably destroy the rotor but im assuming you are replacing them anyway

May 03, 2009 | 1994 Ford Bronco

1 Answer

Replace Front seats in 1994 Bronco


F150 seat should work in the 94 bronco if not you could remove thebraces and sliders of the bronco and put them on the other seats..

Dec 02, 2008 | 1994 Ford Bronco

Not finding what you are looking for?
1994 Ford Bronco Logo

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...