Question about 2004 Oldsmobile Alero

2 Answers

The key will not turn in the ignition switch. The front wheels can turn even with the switch in the off position. Is this simiply a problem with a tumbler? I looked at the "passlock" system but it

I have an 2004 olds alero with a stuck starter key switch. The key will not turn. The front wheels will turn both left and right and never locks in place. Is this related to the passcode security system at all? Or, is the tumbler bad?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had that same problem with my 99 alero i ended up having to change out my entire egnition switch and tumbler

Posted on Jun 11, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I've had the same issue. Go to the dealer and get a new cut key, since keys get worn out, it solved my solution and saved me hundreds of dollars.

Posted on Nov 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove the ignition lock cylinder from a 93 geo storm


is the lock assembly in the car or out?
there are 2 jobs here, removing the assembly
and after that, attacking the lock it self.???????

any lock smith can rebuild the lock, proper
it has pins that are pressed out.
it can even be rekeyed.

the remove assembly is covered in the FSM, no books?
alldata.com covers that.
it really is an Isuzu. impulse.

my guess is its job 1, assembly out.
so toss coin lands on job1
(on most cars, steering wheel must be removed)
once that is done, its obvious from there, right? that clamp there with the antitamper screws? then must be removed. and replaced new..

a rare car , and even more one that runs....

here is the online FSM answer

  1. Remove the negative battery cable.
  2. Remove the steering wheel.
  3. Remove the combination switch assembly.
  4. Turn the key to the OFFposition, depress the retaining pin and remove the ignition lock cylinder from the switch.
  5. Disconnect the electrical connector from the ignition switch.
  6. Remove the snapring and spacer collar from the steering shaft.
  7. Disconnect the back drive cable from the ignition switch.
  8. Remove the ignition switch bolts and the ignition switch from the steering column.


now back in?
  1. Install the ignition switch to the steering column and tighten the bolts.
  2. Connect the back drive cable to the ignition switch.
  3. Install the spacer collar and the snapring to the steering shaft.
  4. Connect the electrical connector to the ignition switch.
  5. Install the lock cylinder into the switch.
  6. Install the turn signal switch screws and the turn signal switch.
  7. Install the four screws and the coil assembly to the turn signal switch.
  8. Connect the coil assembly wiring harness to the turn signal switch.
  9. Install the two piece steering column cover and the two piece steering column cover screws.
  10. Raise the steering column and install the upper steering column mounting bolts. Tighten the bolts to 18 ft. lbs. (24 Nm).
  11. Install the left lower dash trim panel and tighten the lower dash trim panel screws.
  12. Install the lap air deflector and tighten the lap air deflector screws.
  13. Install the knee pad assembly and tighten the five screws, the bolt and the nut attaching the assembly.
  14. Install the engine hood opener cable.
  15. Install the engine hood opener and tighten the two screws.
  16. Connect the electrical connector to the cigar lighter bezel and install the bezel.
  17. Connect the electrical connector to the left switch bezel and install the bezel.
  18. Install the steering wheel.
  19. Connect the negative battery terminal to the battery.

that?

Oct 08, 2014 | 1993 Geo Storm

2 Answers

Ignition is in lock position and won't turn on. saab 2000/ 900 3


make sure the stick is in reverse and the key is all the way in the ignition

May 01, 2012 | Saab 9 3 Cars & Trucks

2 Answers

Steering wheel wont lock and stuck in park


In the fuse block under the drivers side rear seat check the ignition 0 fuse. In the under hood fuse block check the B/U fuse and the BTSI fuse. If the b/u fuse is blown than you would not have back up lamps.

Dec 02, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Ignition is locked


Could be one of the following:
Are the front wheels turned? If so, turn the steering wheel hard, in the same direction as the front wheels while turning the key to towards the ON position. Also try rapidly turning the steering wheel back and forth while trying to turn the key to ON. Also, if you have a tilt steering wheel try moving it up and down as well.

Is your key worn? Try a spare key. Or have a new key made. (may help)

The switch itself is jammed and will have to be replaced.

Aug 01, 2011 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

Ignition switch unable to turn car on key is hard to mget into switch nassemblyn I tried a new key that came with the vehicle


  • Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them.
  • 2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.
  • 3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.
  • 4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.
  • 5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.
  • 6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.
  • Dec 04, 2010 | 2007 Honda Ridgeline

    1 Answer

    How do i remove ignition switch on a 1991 f150 ?


    HI, follow the steps below to help with this issue.



    Step 1

    Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them.

    Step 2

    Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

    Step 3

    Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

    Step 4

    Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

    Step 5

    Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

    Step 6

    Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.



    Jul 11, 2009 | 1991 Ford F150

    1 Answer

    Replacing the ignition switch in a 96 ford mustang cobra svt


    Follow these steps carefully. this will help you achieve this replacement.



    1. Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing them.

    2. Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

    3. Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

    4. Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

    5. Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

    6. Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

    Jun 17, 2009 | 1996 Ford Mustang

    1 Answer

    Hoe to remove the ignition switch in 05 ram 1500


    Step1 Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them. Step2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft. Step3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheelmag-glass_10x10.gif and disconnect the wiring. Slide the spacer sleeve off of the steering column. Step4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out. Step5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder. Step6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

    Feb 21, 2009 | 2005 Dodge Ram 1500

    1 Answer

    Key wont turn in ignition 2006 Corolla S


    have tilt wheel? try unlocking tilt and moving it as you try to turn key..replace key and/or ignition switch if that doesnt work..if it does ..the linkage is damaged in steering column to switch at base

    Dec 08, 2008 | 2006 Toyota Corolla

    Not finding what you are looking for?
    2004 Oldsmobile Alero Logo

    564 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Oldsmobile Experts

    yadayada
    yadayada

    Level 3 Expert

    76070 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8266 Answers

    Are you an Oldsmobile Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...