Question about 1996 Plymouth Voyager

1 Answer

Just replaced brake pads and rotors

The brake pedal goes all the way to the floor now and the car doesnt sopr right away when braking it still ges a little bit

Posted by on

  • demismama May 17, 2009

    where is the bleeder screw on the back tire...I have drum brakes in the back

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

You need to bleed the brakes front right back left ront left back right in that order

Posted on Apr 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 ford taurus brake pedal goes straight to the floor .


Brake line busted somewhere? Is the linkage to the master cylinder intact? Master cylinder might have been installed incorrectly.

Dec 04, 2013 | Cars & Trucks

1 Answer

Next to no Brakes


No, but could be pad knock back which can be caused by run out of the rotors. This can happen if your pads have worn down too far in the past. I'd advise you to have the rotors ground (on the car) and new pads fitted. The fronts are critical but have the rears checked for run out too. Sometimes new seals in the calipers can help hold the pads against the rotors.This will improve the loss of pedal condition.

Mar 18, 2010 | 1999 Ford Escort

1 Answer

Brakes spongy after shop replaced rotors braked pads on 2001 buic


Sounds like air is still in the brake lines, the air sound that you hear is the power assist, but the brake pedal needs to be "high and hard".

if the pedal goes to the floor, that is not good. Sometimes, when pumping brakes for bleeding purposes, the master cylinder gets damaged, as the piston goes past it's normal "travel zone" and gets damged on deposits.....

Now, with that being said, if everything was perfect, brakes are typically not as firm after replacement, due to differences in new pads/shoes and old rotors and drums. Pedal to the floor, however, is never okay.

Doc

Sep 18, 2009 | 1995 Chevrolet Blazer

2 Answers

Brake pedel pushes to the floor


pump the pedal about 10 times and see if it comes back up, u need to pump the caliper pistons out after a brake job.

Jun 27, 2009 | 1997 Ford F150 Regular Cab

1 Answer

LOW BRAKE PEDAL ON 4 WHEEL DISK BRAKES


Check the pads/rotors to see if they need to be replaced.
Check the brake fluid level. If low it could mean the pads/rotors need to be replaced. If replacing also replace the brake fluid.
Two years probably means you need a brake job.

Otherwise you may have air in the brake lines which you can bleed off.

May 07, 2009 | 1999 Chrysler 300M

2 Answers

Changed front brake pads. brake pedal goes to floor. no brakes


Something doesn't sound right, you shouldn't have to remove the brake line to install pads. Did you have to do this on both sides? Do the new pads and the old pads look the same? Did you get the caliper on crooked? Just recheck your work first before replacing more parts. When you install the caliper, You have to hook the pad on one side first before you slide it over the rotor.

Mar 26, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Brakes bad even after replacing pads/rotors


You need to replace the master cylinder. If all else is good and the petal goes to the floor, that's really about all it could be.

Nov 09, 2008 | 1989 Volvo 240

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
1996 Plymouth Voyager Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...