Question about 1995 Chevrolet Monte Carlo

1 Answer

I have a bent arm going out to the wheel hub is

I have a bent arm going out to the wheel hub is this called a stabilizer bar, or something else?

Posted by on

  • playgent Apr 22, 2009

    The component I am referring to is on the rear axle

  • Anonymous Mar 27, 2014

    there are two steel bars running from the center of the rear axle out to the bottom of the strut assembly, mine are bent and no one seems to know if they are a control arm or a stabilizer bar... or where I can get them.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

It's called the CV Joint if that's is the arm you are try to describe. The CV Joint should be connected to the front wheel hub and the other end to the transmission. It may look bent but that's normal unless it's the bar it self. Only the ends should seam like it's bent.
Good luck and hope this helps

Posted on Apr 22, 2009

  • Harvey N Tawatao
    Harvey N Tawatao Apr 22, 2009

    The rear suspension only has a few components. 


    Hope this helps: There is a stabilizer bar that connect's to the Rear Lower A  Arms which holds the Rear Hub assembly and Strut assembly. 


    Those are the three major components. Thinking it's the stabilizer bar your asking, but some poeple know them as sway bar's


    Good luck 

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Front driver side leaning inward, have changed strut,etc...


Upper and lower ball joints. Control arm bushings bad. or both.

Jul 09, 2016 | Cars & Trucks

2 Answers

I have a 02 explorer and when I drive the steering wheel shakes right to left.I changed stabilizing pins...nothing....please help


sounds like a bent wheel or a separated tire. should be pretty easy to spot by spinning the tires by hand.

Aug 20, 2015 | Cars & Trucks

1 Answer

How to install rear struts on a 1999 llexus


selectachapter.gif

Lexus Car ES, IS, LS 1998-06
Coil Spring Rear Suspension

Print


Hub & Bearings

Adjustment
Check the backlash in bearing shaft direction and the axle hub deviation. Maximum for backlash should be 0.0020 in. (0.05mm) and for axle hub deviation 0.020 in. (0.05mm).

7923lgb6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Checking wheel bearings for excessive play


NOTE The rear wheel bearings are non-adjustable. If the wheel bearing is out of specifications, replace the wheel bearing.
Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:

    Rear tire and wheel assembly Rear stabilizer link Rear axle shaft nut Rear disc brake caliper and disc Speed sensor Parking brake assembly at the wheel hub No. 1 and 2 upper control arm assembly No. 1 and 2 rear suspension arm assembly Toe control link Rear axle from hub assembly using a plastic hammer No. 2 rear wheel bearing dust deflector using a screwdriver 4 bolts and rear axle hub and bearing assembly from the axle carrier assembly

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 52 ft. lbs. (70 Nm) No. 2 rear wheel bearing dust deflector using a screwdriver Rear axle into hub assembly No. 1 and 2 upper control arm assembly. Torque the new nut to the No. 2 rear upper control arm to 52 ft. lbs. (70 Nm). Temporarily tighten the No. 1 arm bolt. No. 1 and 2 rear suspension arm assembly. Temporarily tighten. Toe control link. Torque new nut to 52 ft. lbs. (70 Nm). Rear stabilizer link. Torque to 20 ft. lbs. (27 Nm). Parking brake assembly at the wheel hub Rear speed sensor Rear axle shaft nut. Torque to 214 ft. Lbs. (290 Nm) and stake the nut with a chisel and hammer. Rear brake disc and disc brake caliper
  2. Adjust the parking brake.
  3. Stabilize the suspension as follows :
    1. Install the wheel(s).
    2. Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
    3. Raise the vehicle.
    4. Remove the wheel.
    5. Jack up the rear lower suspension armplacing a wood block in between. Apply a load to the suspension so that the lower suspension arm is plkaced in a horizontal position.

  4. Fully tighten the No. 1 rear upper control arm assembly to 119 ft. lbs. (161 Nm).
  5. Fully tighten the No. 1 rear suspension arm assembly to 70 ft. lbs. (95 Nm).
  6. Fully tighten the No. 2 rear suspension arm assembly to 119 ft. lbs. (161 Nm).

    Rear tire and wheel assembly

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:
    NOTE If it is necessary to replace the hub or bearing, replace the components as an assembly.


    Rear tire and wheel assembly If equipped with rear disc brakes, the caliper mounting bolts. Leave the brake line connected and suspend the assembly out of the way. Brake rotor or drum 4 bolts and pull off the rear axle hub O-ring

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 59 ft. lbs. (80 Nm) Rotor or drum Caliper, f equipped with rear disc brakes and tighten the bolts to 34 ft. lbs. (64 Nm) Wheel

  1. Before servicing the vehicle, refer to the Precautions section.
  2. If equipped with air suspension, move the height control switch in the trunk area to the OFF position.
  3. Remove or disconnect the following:

    Negative battery cable Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Cotter pin, lock cap and the nut holding the halfshaft to the rear axle Suspension member brace by removing the 2 bolts Halfshaft bolts and washers Halfshaft from the vehicle Strut rod
  4. Place matchmarks on the adjusting cam and body for the No. 1 control arm.
  5. Remove or disconnect the following:

    Nut and adjusting cam Nut on the axle carrier side of the No. 1 lower control arm Separate the control arm from the axle carrier No. 1 lower control arm Stabilizer bar link from the No. 2 lower control arm.
  6. Place matchmarks on the adjusting cam and body.
  7. Remove or disconnect the following:

    Nut and adjusting cam from the No. 2 lower control arm Nut and bolt holding the No. 2 lower control arm to the axle carrier No. 2 control arm from the vehicle Nut and bolt on the lower side of the strut assembly 2 upper control arm set nuts and bolts Axle carrier with the upper control arm
  8. Secure the axle carrier in a vise.
  9. Remove or disconnect the following:

    Nut holding the upper control arm to the axle carrier and remove the control arm Dust deflector. Use a suitable prytool. Oil seal

    0996b43f802092da.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (inner)-LS 430

  10. Remove the 2 bolts and nuts and shift the backing the plate towards the hub side (outside).
  11. Remove or disconnect the following:

    Axle hub

    0996b43f802092db.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the axle hub from the axle carrier-LS 430
    Backing plate. Inner race (outside) from the axle hub

    0996b43f802092dc.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the inner race (outside) from the axle hub-LS 430
    Oil seal (outer) from the axle

    0996b43f802092dd.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (outer)-LS 430
    Snapring from inside the axle housing Bearing from the axle housing


To install:
  1. Install or connect the following:

    New bearing to the axle housing Snapring to the axle carrier, using snapring pliers New outer oil seal. Coat the oil seal lip with multipurpose grease.

    0996b43f802092de.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (outer)-LS 430
    Backing plate to the axle housing. Do NOT install the bolts or nuts at this time. Inner race (inside) to the axle housing Axle hub to the axle housing Backing plate in position. Tighten the bolts and nuts to 43 ft. lbs. (59 Nm). New oil seal (inner) to the axle housing. Coat the oil seal lip with multipurpose grease.

    0996b43f802092e0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (inner)-LS 430
    New dust deflector. Be sure to align the hose for the ABS speed sensor in the dust deflector and axle carrier. Upper control arm to the axle carrier by installing the nut. Tighten the nut to 80 ft. lbs. (108 Nm). Axle carrier and upper control arm to the vehicle as an assembly 2 upper control arm set bolts and tighten the bolts to 121 ft. lbs. (164 Nm) Bolt and nut holding the strut to the axle carrier. Tighten to 101 ft. lbs. (137 Nm). Bolt and nut connecting the No. 2 lower control arm to the axle carrier. Tighten the bolt to 60 ft. lbs. (81 Nm). Nut and adjusting cam to hold the No. 2 lower control arm to the body. Align the adjusting cam marks and tighten the nut to 57 ft. lbs. (78 Nm). Stabilizer bar link to the No. 2 lower control arm and tighten the nut to 48 ft. lbs. (65 Nm) No. 1 lower control arm to the axle carrier and body. Install the nut to hold the No. 1 lower control arm to the axle carrier. Tighten the nut to 43 ft. lbs. (59 Nm). Nut and adjusting cam to hold the No. 1 lower control arm to the body. Align the matchmarks and tighten the nut to 57 ft. lbs. (78 Nm). Strut rod to the axle carrier and body. Install the bolt and nut to hold the strut rod to the body. Tighten to 57 ft. lbs. (78 Nm). Bolt and nut to hold the strut rod to the axle carrier. Tighten to 136 ft. lbs. (184 Nm) Parking brake shoes and cable Outboard joint side of the halfshaft and align the matchmarks on the side gear shaft and the halfshaft. Coat the threads with clean oil and install the hexagon bolts. Tighten bolts to 61 ft. lbs. (83 Nm). Suspension member brace with the 2 bolts. Tighten the 2 bolts to 37 ft. lbs. (50 Nm). Nut to hold the halfshaft to the rear axle. Tighten the nut to 213 ft. lbs. (289 Nm). Lock cap and cotter pin Brake disc to the axle hub with the matchmarks aligned. Install the 2 screws and tighten the screws to 48 inch lbs. (5 Nm). Brake caliper to the vehicle and install the 2 bolts. Tighten the bolts to 77 ft. lbs. (104 Nm). ABS speed sensor and wiring harness Height control sensor link with the matchmarks aligned. Tighten the nut to 48 inch lbs. (5 Nm). Rear wheel(s) Negative battery cable

  2. Lower the vehicle and turn ON the air suspension switch.



0996b43f80207fdc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear carrier assembly, hub and bearing-

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    WARNING Be careful not to damage the boot and ABS sensor


    Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Toe control link Separate upper control arm assembly Shock absorber from axle carrier Suspension arms No 1 and 2 from axle carrier Rear axle from carrier


    Wheel bearing dust deflector 4 bolts and axle & bearing hub assembly

To install:
  1. Install or connect the following:

    4 bolts and axle & bearing assembly. Tighten to 48 ft. lbs (65 Nm) Rear wheel bearing dust deflector Rear drive axle Upper control arm. Temporarily tighten No 2 and No 1 suspension arms. Tighten to 52 ft. lbs. (70 Nm) Shock absorber. Temporarily tighten Toe control link. Tighten to 37 ft. lbs. (50 Nm) Fully tighten upper control arm. Tighten to 52 ft. lbs. (70 Nm) Height control sensor Parking brake shoes and cable Speed sensor Rear disc brake caliper Fully tighten shock with new nut to 52 ft. lbs. (70 Nm) Rear tire
  2. Inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear wheel Wheel speed sensor Axle halfshaft Brake caliper and rotor Parking brake shoes Parking brake cable No. 1 lower suspension arm bolt No. 2 lower suspension arm bolt Toe control link Upper ball joint Axle carrier from the vehicle
  3. Press the hub out of the wheel bearing, then remove the backing plate.
  4. Remove the snapring, then press the wheel bearing out of the axle carrier.

To install:

NOTE Use a new toe control link nut for assembly.
  1. Installation is the reverse of the removal procedure, while using the following torque values:

    Backing plate bolts: 43 ft. lbs. (59 Nm) No. 1 lower suspension arm bolt: 55 ft. lbs. (75 Nm) No. 2 lower suspension arm bolt: 81 ft. lbs. (110 Nm) Toe control link nut: 36 ft. lbs. (49 Nm) Upper ball joint nut: 80 ft. lbs. (108 Nm) Brake caliper support bolts: 77 ft. lbs. (104 Nm) Rear wheel lug nuts: 76 ft. lbs. (103 Nm)



0996b43f80208026.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear Axle carrier and hub assembly-ES 330

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear tire and wheel assembly Brake caliper support bracket Brake rotor Skid control sensor wire 4 bolts and rear hub and bearing assembly Skid control sensor

To install:
  1. Install or connect the following:
    NOTE Inspect bearing back lash and hub deviation


    Skid control sensor Rear axle hub and bearing assembly with 4 bolts. Tighten to 59 ft. lbs. (80 Nm) Skid control sensor wire


    Rear disc Rear disc brake caliper assembly. Tighten to 46 ft. lbs (62 Nm) Flexible brake hose Rear tire and wheel
  2. inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal


Stabilizer Bar

Removal & Installation

  1. Remove the rear wheels.
  2. Remove the 2 nuts and left stabilizer bar link. If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud. Repeat for the right side.
  3. Remove the 8 bolts, 2 No. 1 brackets and 2 bushings. Two types of bolts are used, so make sure the correct bolts are installed.
  4. Remove the stabilizer bar.

To install:
  1. Install the stabilizer bar.
  2. Install the bushing and bracket with the 2 bolts and tighten to 14 ft. lbs. (19 Nm). Install the bushing to the inner side of the bushing stopper on the stabilizer bar.
  3. Connect the stabilizer bar links and tighten the nuts to 29 ft. lbs. (39 Nm). Repeat for the right side.
  4. Install the rear wheels.
  5. Inspect and adjust rear wheel alignment.


Strut & Coil Spring

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    CAUTION Do NOT remove the center nut to the strut at this time. The spring on the strut is under high pressure and can cause serious injury.


    No. 2 luggage compartment trim cover Left and right deck side trim box Rear luggage compartment trim cover Front luggage compartment trim cover Left and right side luggage compartment trim covers Rear wheel Rear wheel fender liner No. 2 differential support protector Rear suspension member brace Rear No. 2 lower control arm Mounting bolts and strut assembly
  3. Secure the strut in a vise.
  4. Compress the coil spring
  5. Remove or disconnect the following:

    Upper strut retaining nut Suspension support Upper insulator Bumper Coil spring Insulator

Dec 26, 2011 | 1999 Lexus ES 300

1 Answer

Can I drive a Pontiac Grand Prix with a broken rear stabilizer safely?


By rear stabilizer, do you mean trailing arm or sway bar? If you have a busted trailing arm, I highly advise against driving. This is the bar that runs from the wheel hub transversely toward the front of the car and attaches to the frame. However, a busted rear sway bar, which runs transversely across the vehicle and runs along side the leaf spring, isn't as severe of an problem. You will just run into spongy turning issues.

Jan 27, 2011 | 1994 Pontiac Grand Prix

1 Answer

2000 gmc z71 passenger side cv joint is making noise when i turn......i talk to napa and can get rebuilt for 60$.....but to take it apart....do i need ball joint separator.....what tools..????


Never use a tool myself other than a big hammer. Those forks don't work for me, though we have them. Hit the joint on the side and it will pop out. If not, you can always put the nut back on even with the ball stud and hit it from the bottom. The book also calls for a special tool to get the axle out of the hub. Have never used this either. If it doesn't slide out, I just hit it--I have a new one anyway (take it loose from the tranny before hitting it). Tools you will need are the big socket for the axle nut (around 22mm or so) and regular metric socket set, preferably 1/2 in drive. Also take the speed sensor and brake lines off the support bracket to free up the hub a little more. Note that you may need to also separate the tie rod end if you cannot otherwise swing the hub out far enough to get the shaft out. The book says to take off the stabilizer and shock and also separate the upper ball joint. I don't know if that's necessary or not, as I have not done one on this particular truck. You are doing the whole shaft, right? We don't do individual CVs anymore, as the labor is ridiculous compared to the cost difference to a whole half shaft. Take the axle nut off, unbolt the shaft from the tranny, and swing the hub out. Pull the axle out of the hub first, then the tranny. Reverse procedure to install. I will paste the book solution from autozone.com below. Lemme know if you have more questions.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheel and tire assembly Skid plate, as required. If equipped Drive axle hub nut and washer Brake line and wheel speed sensor support bracket from the upper control arm to allow extra travel of the control arm. Left outer tie rod attaching nut and cotter pin. Separate the tie rod from the steering knuckle
  3. Position the tie rod aside and push steering linkage to the opposite side of the vehicle.

    Lower shock attaching nut and bolt; position the shock aside Left stabilizer bar bracket and bushing at the frame Stabilizer bar bolt, spacer and bushings at the lower control arm
  4. Taking pressure off the upper control arm by placing a support below the lower control arm between the spring seat and the ball joint.
    NOTE Cover the shock mounting bracket and lower ball joint stud with a towel to prevent the axle boot from tearing during removal and installation.


    Upper ball joint cotter pin and loosen (do not remove) the upper ball joint attaching nut. Separate the ball joint stud from the steering knuckle. Remove the attaching nut.
  5. Separate the axle shaft from the hub and rotor using tool J-28733 or equivalent.

    Axle shaft inner flange bolts and shaft
To install:
  1. Lubricate the axle and hub splines with an approved high temperature wheel bearing grease.
  2. Install or connect the following:

    Axle shaft in the hub Inboard CV-joint-to-flange bolts. Torque the bolts to 60 ft. lbs. (80 Nm). Upper ball joint to steering knuckle. Torque the stud nut to 61 ft. lbs. (83 Nm). New cotter pin through the upper ball joint stud and nut, lubricate the ball joint as required. Left stabilizer bar bracket and bushing at the frame Stabilizer bar bolt, spacer and bushings at the lower control arm Lower shock in the mount bracket and the attaching nut and bolt Left tie rod end at the steering knuckle. Torque the nut to 35 ft. lbs. (47 Nm). New cotter pin through the tie rod stud and nut Brake line bracket to the control arm, ensuring the line and/or hose is not twisted or kinked Skid plate, as required Axle hub washer and nut. Insert a drift through the rotor vanes to keep the axle from turning. Toque the hub nut to 180 ft. lbs. (245 Nm) Wheel and tire assembly

Oct 26, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Driver side lower control arm how do i install new one


  1. Raise and support the vehicle with safety stands. Refer to Vehicle Lifting.
  2. Remove the tire and the wheel. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
  3. Unload the torsion bar. Refer to Torsion Bar and Support Assembly Replacement
  4. Remove the wheel driveshaft nut and washer.
  1. Disengage the wheel driveshaft from the wheel hub and bearing assembly. Place a brass drift against the outer end of the wheel driveshaft in order to protect the wheel driveshaft threads. Sharply strike the brass drift with a hammer. Do not attempt to remove the wheel driveshaft from the wheel hub and bearing assembly at this time.
  2. Remove the stabilizer shaft. Refer to Stabilizer Shaft Replacement (RWD) or Stabilizer Shaft Replacement (4WD).
  3. Remove the shock absorber. Refer to Shock Absorber Replacement (RWD) or Shock Absorber Replacement (4WD).
85105731
  1. Remove the nuts and bolts securing the lower control arm to the crossmember and the frame bracket.
  2. Remove the lower ball joint stud from the steering knuckle. Refer to Lower Ball Joint Replacement (RWD) or Lower Ball Joint Replacement (4WD).
  3. Remove the lower control arm from the frame.






have fun and be careful wear always lens and gloves

Oct 21, 2010 | 2000 Oldsmobile Bravada

1 Answer

I need a rear suspension diagram for a 1999 Mercury Cougar


0218b1b.gif
Item Part Number Description 1 Body mounting cup 2 Spring seat 3 Spring 4 Strut 5 Crossmember 6 Stabilizer bar 7 Front arm 8 Rear arm 9 Wheel spindle 10 Tie-bar 11 Dust cap 12 Brake drum 13 Hub retaining nut 14 Hub and bearing assembly 15 Backing plate 16 ABS sensor 17 Tie-bar mounting bracket

Sep 02, 2009 | 1999 Mercury Cougar

1 Answer

I need the rear shock torque specs for a 2007 sport trac


Torque Specifications Description Nm lb-ft lb-in Brake caliper bolt 32 24 — Brake disc shield bolt 8 — 71 Fuel tank filler pipe bracket bolt 15 11 — Fuel tank filler pipe hose clamps 3 — 27 Halfshaft nut and washer 275 203 — Lower arm inboard bolt 250 185 — Lower arm outboard bolt 275 203 — Parking brake cable bracket bolt 10 — 89 Shock absorber lower bolt 275 203 — Shock absorber rod nut 65 48 — Shock absorber upper mount nut 30 22 — Stabilizer bar bracket nut 48 35 — Stabilizer bar link nut and grommet 30 22 — Toe link cam adjuster nut 275 203 — Toe link outboard bolt 325 240 — Trailing arm bolt 300 222 — Upper arm outboard bolt 225 166 — Upper arm inboard nut 250 185 — Wheel speed sensor bolt 8 — 71 Wheel knuckle bolt 275 203 —

Mar 30, 2009 | 2007 Ford Sport Trac Limited

2 Answers

Snapped a bar that holds rear tire from moving front and back


yes you are right . and it can be replaced BUT i would look a little more.he may have a bent sturt and other parts.he hit the curb very hard to break the stablizer bar.

Mar 22, 2009 | 1992 Ford Taurus

3 Answers

SLID INTO CURB SIDEWAYS -- DAMAGE?


Front:
  1. May have bent upper/lower a-arm: used parts & Labor $250
  2. May have damaged splines on 1/2 shaft: new prts & Labor $400 (should be replaced in pairs)
  3. May have bent rim/hub : Used Parts & labor $200
  4. May have bent Strut Tower: New Parts & Labor $100 (should be replaced in pairs)
  5. May have bent sway or stabilizer Bar: Parts&Labor $200
Rear:
  1. Not too much involved in rear for these cars: New rim/tire Used for $75
  2. Bent upper/lower A Arm: $250
Civics are popular vehicles, and many new and used parts can be had on eBay or your local Salvage. Unless you specify, and they are willing, most repair shops will only replace with new parts, because they will not warranty the used ones.
Your bill could easily reach the point of totalling the vehicle. It may be cheaper for you to purchase another vehicle. Get a free estimate at a mechanic and weigh your options.

Dec 24, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1995 Chevrolet Monte Carlo Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...