Question about 1999 Ford Taurus

1 Answer

Hi i bought a code reader and these codes came up when my 1999 ford taurus was running,they are P0340 and P1400 what do they mean and what is the fix if some one know please

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

PO340 is the camshaft position sensor needs replacing.
P1400 is Differential Pressure Feedback sensor is bad.

Posted on Apr 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced cam shaft sensor on 2005 ford taurus and still get code p0340. Possible fix distributor? According to AutoZone computer suggested parts.


This means the sensor isn't working. That can be caused by a bad connector or broken wire.
Check the connections to the camshaft sensor. don-ohio (:^)

Dec 15, 2016 | Ford Cars & Trucks

1 Answer

Have a 1997 ford explorer with 4.0 sohc that died at stop and would not start. cranked but no start. error code was p0340. replaced crank sensor and started but died again in less than 2 minutes. still...


p0340 states: Cam Position Sensor A circuit (Bank 1, or single sensor)

p1318 : unknown code cannot find online or in my code reader definitions.

remember the code does not mean the part is bad just where to look for bad wires, connectors and to test for bad parts.

Sep 16, 2012 | Ford Explorer Cars & Trucks

3 Answers

My 2002 Ford Explorer gave me code P1400. What does it mean


P1400 indicates the following:
Differential Pressure Feedback Electronic Sensor circuit Low Voltage

Most common cause is a bad DPFE sensor.

Jul 15, 2011 | 2002 Ford Explorer

1 Answer

Have 2002 Ford Taurus SE and testing at auto zone brought up code P1400, can you tell me what this mean? Thank you, Shawna Hughes


That would be your DPFE sensor low voltage. This is the feedback sensor for the egr valve and it has exhaust gases running through it at basically all times. They have 2 different styles (plastic and aluminum) and they all fail eventually. The replacement should be plastic which typically lasts longer in my experience. It should be under $50 and fairly easy to replace. I recommend replacing the rubber hoses as well since they crack and will probably break during removal or soon after.

Jun 23, 2011 | 2002 Ford Taurus

2 Answers

Can u tell me what the problem of this code PO340


I have a 1999 BMW 740 il My SES light came on so I hooked up my OBD code reader p0340 - Camshaft Position Sensor Circuit Malfunction is what came up. so I went to the BMW parts department and bought the Camshaft Position Sensor.
I Replaced the with the new. My SES light was still on so I hooked up the OBD reader again hoping it may reset my SES light but it didn't what did happen is the OBD reader came up with the same code (p0340 - Camshaft Position Sensor Circuit Malfunction) witch is what I just replaced. now I'm at a loss. I'm not sure how to reset my SES light and if I just replaced the Camshaft Position Sensor why dose it the OBD code p0340 still come up. Any suggestions?

Mar 18, 2011 | 1996 Nissan Altima

1 Answer

98 Taurus P0340 code still present after replacing camshaft sensor and synchronizer. Car not starting all the time. I do not see the spark when car will not start. Then replaced the crank sensor. Still...


all ways turn the motor over a few times and recheck timing marks a slack belt can put it a tooth out, if the code is back it means the fault is still there, did they remove the code and test drive if so the fault is not fixed.

Mar 31, 2017 | 1998 Ford Taurus

1 Answer

My Ford Taurus just failed a vehicle emission test due to diagnostic codes P0401, P0402, and P1400. Can you tell me what these codes are for and what type of repair is needed? Thanks.


plz check the fuel and carborater first then go for silencer (if your car runned above 15000 kms got repair shop) even u can neglet, coz thees error come during winter sesion [they are related to carben and moister]

Jun 23, 2010 | 2002 Ford Taurus

3 Answers

Wat does code p1400 means


In order to give you accurate information. I need size of engine example 2.0 L 3.0L. but code P1400 means Differential Pressure feedback EGR circuit low input. Maybe your differential oil is low.

Apr 01, 2010 | 2002 Ford Taurus

1 Answer

03 Taurus with DTC P0340, P1336


I would think it would be just the Camshaft Position Sensor.I looked up the codes and they say pretty much the samething.


P0340 Ford Camshaft Position Sensor Circuit Malfunction


P1336 Ford Crankshaft/Camshaft Sensor Range/Performance












Jan 18, 2009 | 2003 Ford Taurus

1 Answer

1999 ford contour, 2.0 dohc The code P0340 set and the car has no power


This code is set the camshaft position sensor, it is part of the ignition system, this can cause your loss of power.

Jul 19, 2008 | 1999 Ford Contour

Not finding what you are looking for?
1999 Ford Taurus Logo

Related Topics:

439 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...