Question about 1987 Toyota Pickup

1 Answer

Just had new head gasket and timing gear and chain put in 86 22r

Just had head gasket and timing gear and chain put in my 1986 toyota 22r engine. i don't know if they have vacuum mixed up or timing off. going down hill when you let off accelerator the truck will **** back and forth while deceleration is happening. when you accelerate to go up the hill it smooths out. is this in vacuum or timing. i haven't had time yet to check the problem out. could it be distributator cap and rotar button? i replaced the wires and plugs when they did the job. this is my only vehicle. what can i say its paid for and i am on a fixed income.

HELP ME PLEASE!!!!!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 53 Answers

Check vacuum lines also check timing with a timing light it shuld be set on 5 degrees not zero also check if it retards or advances

Posted on May 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I remove gear-to-gear timing cam?


images for How to remove a gear to gear timing cam ...

DIY Timing Chain and Gears Removal - YouTube

? 6:31
https://www.youtube.com/watch?v=eMXO1bvUCMs
Dec 30, 2012 - Uploaded by Bullshitkorner
The most important part when doing timing gears on a engine is ... Doing this inside the engine bay will be a bit of a pain in the axx but it is doable for sure. ... How to build a Chevy 383 Part 3: How To Install a Cam & Timing ...

Head removal & replacement, Timing Chain & gears also ...

? 3:28
https://www.youtube.com/watch?v=CnXtwR1N0Og
Apr 28, 2012 - Uploaded by No1hmfic Gibson
Head removal & replacement, Timing Chain & gears also, 97 Chevy S10 2.2 ... replacing the head gasket in a chevy cavilier 2.2 liter 4 cylinder - Duration: 9:38. ... 98 S10 Vortec V6 4.3 Intake Gasket Replacement Part 1 of 5 ...

Chevy S 10 2.2 L Engine Timing Chain Replacement Guide ...

? 7:30
https://www.youtube.com/watch?v=8nX5HARPSF4


Feb 03, 2016 | 1998 Chevrolet S-10 Pickup

1 Answer

1994 nissan pu starter drags when engine is warm, new starter,new battery. new timing chain & gear, valve job,head gasket


1. Make sure all the high-current battery and starter connections are clean and shiny. Don't just wipe them off; get one of those battery terminal cleaners that scrapes off the top layer of oxidation. Use a wire brush on connections the battery cleaner doesn't fit. Remove each connection, clean it and put it back.

2. Be sure the timing is set correctly.

3. If there was a heat shield on the starter, make sure it's still there.

4. Get the starting system checked at an auto parts store. Maybe you got a bad battery or starter.

Jan 18, 2015 | 1994 Nissan Pickup

1 Answer

Toyota engine 1rz


if you over heated the engine you could have a warped engine blockor a crack or did not properly install new head gasket .did you properly torque down the head bolts?

Mar 24, 2014 | Cars & Trucks

1 Answer

Is there a timing belt or gear on a 1986 toyota tercel


Timing belt for sure.If there is a plastic cover on the front of the engine behind the drive belts then its a timing belt and not a chain.
hope this helps,
Kenneth R.

Oct 08, 2010 | 1986 Toyota Tercel

1 Answer

Replaced head. Now can't get engine timed


i just rebuilt my 22r you have to make sure the chain is set on the timing gears properly also when you put the distributer in you have to find tdc on the #1 cylinder on the compression stroke. the piston travels and the valves open and close after the exhaust valve opens and closes the intake valve will open as the piston travels down when it closes the piston will travel back up compresing the fuel when the dot on the crank lines up with the mark on the timing cover that is tdc top dead center on the compresion stroke. once you have that yoo slide in th distributor so as the rotor points at the number one contact on the cap

Oct 24, 2009 | 1986 Toyota Pickup 4WD

1 Answer

1986 toyota pickup won't turn over


Will it turn over by hand, as in socket wrench on front pulley, and try to slowly turn it over. Also check that #1 cylinder on compression stroke, and TDC, your rotor under distributor cap is pointing at the plug wire tab under cap for #1 cylinder.

Nov 22, 2008 | 1986 Toyota Pickup 4WD

1 Answer

Timing chain


I'll assume you are going to replace the entire set (sprockets, guides, etc.) which I got from O'Reilly for $79.

First, set engine to #1 TDC.
Remove valve cover, fan shroud, fan, drive belt, water pump, 4 10mm bolts from bottom front of head, and 3 10mm bolts from front of oil pan. Remove lower front shield to remove oil pump. remove oil pump/distributor drive shaft, noting the orientation of the drive shaft.
Remove harmonic balance using correct puller (can be rented from local auto parts store). Remove P/S pump and A/C compressor if necessary. Remove timing cover.

IMPORTANT: Before removing oil thrower and distributor drive gear, note direction of oil thrower.
Remove oil thrower and distributor drive gear.
Remove chain guides, tensioner, chain, and finally both sprockets.
The new crank sprocket can only be installed one way, by aligning groove with keyway. The new cam sprocket will have 3 guide holes on the mounting flange, and you will need to align the knock pin with hole #2. Both sprockets should have a small dot (timing mark) on the right side of the sprocket when viewed from the front.
To install new chain, inspect chain to find the two brightly colored gold links. These two links must align with the timing marks on the sprockets. Assemble and install chain tensioner.

!!! IMPORTANT: Be sure to use new gasket when installing tensioner. Tensioner is oil pressure fed and a leaking gasket could allow chain slack, leading to premature wear or break.
Install chain guides, being sure not to let tensioner pop out.

!!! IMPORTANT: The tensioner must be fully compressed. To accomplish this, loosen the 8mm bolts in the passenger side guide (the shorter one). Compress the tensioner, adjust guide to remove slack, and tighten the two 8mm bolts.
Double check that everything is still lined up properly, and make corrections as necessary.
Install distributor drive gear and oil thrower.

!!! IMPORTANT: Ensure oil thrower is installed facing away from the distributor gear. If not, it could get caught in the distributor gear and destroy the two gears or cause engine lockup.

Before installing timing cover, inspect coolant and oil passages. If there is excessive buildup, a good system cleaner is recommended. Replace timing cover gaskets to prevent oil leakage. The best way to reinstall the timing cover is to remove the oil pan, install the timing cover, and reinstall the oil pan (replacing the pan gasket). If you don't want to do that, simply grease the top and bottom of the timing cover and lightly tap it into place with a rubber mallet. This is to prevent damage to the oil pan and head gaskets.
To install the distributor drive shaft, dab some grease on the top side of the gear to hold it in place, and line it up with the distributor. If you are having trouble lining up the shaft, pull it out and look at it from the top, and you will see that the flange is offset. At #1 TDC, the offset will be towards the front.
Install oil pump, being sure to use new gasket.

!!! IMPORTANT: Failure to replace oil pump gasket could lead to inadequate oil pressure, which will cause severe engine damage.

The remainder of the installation is a reverse of removal, using new gaskets where necessary. Before installing your valve cover is a good time to check your rocker arm clearances. This is also a good time to replace your drivebelt, and any other maintenance items as necessary.

Sep 11, 2008 | 1986 Nissan King Cab

Not finding what you are looking for?
Cars & Trucks Logo

362 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...