Question about 1989 Toyota Land Cruiser

1 Answer

CLUTCH PLATE WHICH WAY DOES THE CLUTCH PLATE FIT IN A HJ75 LANDCRUISER 1989 MODEL, ON END OF THE COUPLING GOING THROUGH THE CENTER OF THE PLATE IS LONGER THAN THE OTHER

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Aaron , the flatter side of the clutch plate goes to the flywheel. Cheers

Posted on Apr 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel economy HJ75 landcruiser ute 1989 with turbo


Check that the intercooler is in good condition (no cracks or leaks) and the hoses are tight at the hose clamps . Next talk to a diesel pump repair specialist as you may have to re-tip the injectors and re-calibrate the pump for the extra air that the turbo produces. Check that you have the correct turbo for the diesel

Mar 14, 2014 | Toyota Cars & Trucks

1 Answer

1998 Toyota Landcruiser Prado drive issue


If the car heats up trying to generate revs , then it Seems like the clutch plate is slipped.

Feb 24, 2014 | Cars & Trucks

1 Answer

Clutch installation


Genewrally speaking you need to remove the gear box. UNdo the bolts holding the clutch pressure plate on the flywheel. . Do this by undoing each bolt a few turns at a time. Remove pressure plate and clutch plate. Clean flywheel face. Remove bearing at center of crankshaft and replace as it will be dry and probably rusty. Fit new clutch plate taking care to observe the correct way the plate is fitted. Normally the raised hub section faces away from the flywheel. THis can be checked by pressing the plate against the flywheel and turning it and it it hits the crank bolts you have it in the wrong way round. Fit the pressure plate over the plate and insert the bolts. Some units have 2 or 4 bolts longer than the restand this is to allow the plate to be depressed a fraction to allow the other bolts to screw in. Place a clutch aligning tool through the clutch plate and into the bearing. Evenly retension the pressure plate bolts going alternately across the cover a bit at a time . When retensioned remove the clutch aligning tool. Remove and replace the throw out bearing on the clutch release forks. Ensure that the clutch kit is all new as mixing parts will not work. Refit the gear box. Basically that is the proceedure but to be exact get the manual for your vehicle to cover any extra steps needed for that vehicle.

Mar 07, 2013 | Ford Transit Connect Cars & Trucks

1 Answer

1979 landcruiser clutch did not release fully to get it into gear.I had rebuild the master and slave silinders.The problem is stil the same.


Problem might be on the Clutch plate is won or Preasure plate is weak wants to be changed. or sometimes your slave cylinder is won inside, fix complete new one and then see before going deep in the gearbox.

Aug 27, 2011 | Toyota Land Cruiser Cars & Trucks

1 Answer

How to replace the clutch on front wheel drive cars


It is best to replace the clutch driven plate, pressure plate and release bearing at the same time.
You have to remove either the transmission or the engine(or both). On some vehicles it is not possible to remove the engine without the transmission. I prefer removing the transmission only, since it does not require a hoist. (Removing engine and transmission complete is a bit more complicated,theres much more things to disconnect, but makes things easier when mating the transmission to the engine after replacing the clutch assembly). When removing the transmission only make sure the engine is properly supported, since the engine is supported by the transmission and vise versa.
Take note of all pipes and cables that you remove and mark them with masking tape since that gives you something to write a description on. Remember to mark the spot that you disconnect from as well. Taking close-up pictures of the engine bay will work wonders when your memory fails.
Read through this : http://www.fixya.com/cars/t4984410-remove_front_axle_get_engine (solution 2)
Drain transmission oil. Remove the driveshafts as described. Remove any electrical connections to the gearbox.
Remove the gearshift linkage. Remove the clutch cable/clutch operating mechanism(hydraulic clutch) Remember to support the engine before unbolting the transmission from the engine. Remove any mountings still connecting the transmission to the body of the car..
Remove the transmission from the engine bay. It is possible to do this by hand (a helper would be a plus at this point)
The clutch pressure plate is then visible on the engine and held in place by 6 bolts. It can be removed along with the clutch plate(which will drop free once the pressure plate is removed. Replacing the clutch is pretty straightforward, except that the clutch plate needs to be centered, or the transmission wont go back on. Autozone stocks a clutch centering tool which you can purchase although some clutch kits come with the centering tool supplied, else you can fashion one out of a wooden dowel. The dowel needs to fit snugly into the recess in the centre of the flywheel. Use insulation tape to build it up if it is too thin. The clutch plate can go in one way only. You will note that the clutch plate centre has a metal plate fitted on one side. This is the transmission side of the plate. Fit the clutch plate and pressure plate to the flywheel and tighten the bolts just enough to hold the clutch plate in place so that it doesnt move around. Using your centering tool make sure the clutch plate is nicely centered. Then tighten the bolts to the specified torque. Which means tighten them up without breaking them. Get the transmission fitted to the engine. This may take some doing especially if the clutch centering didnt go too well. Now reconnect everything and drive the vehicle to the nearest alignment centre to re-set the wheel alignment.

Jul 07, 2010 | Cars & Trucks

1 Answer

Where is the torque converter and drive plate on 97 eclipse gst manual transmission.. so i may markmatch it before removing the tranny


hi, if you have a manual gearbox then you dont have a torque converter a torque converter is what changes the gears in an automatic gearbox as your is manual all you will have inside your gearbox is a pressure plate a clutch plate and a thrust bearing witch operates the clutch when you press the pedal down.
The only thing you need to line up on a manual box is when you have fitted the new clutch you need to have a tool that holds the clutch plate central so that when you tighten the bolts up on the pressure plate the clutch stays central if you dont do this you wont be able to get the gearbox back onto the engine as the spline from the gearbox wont be able to go through the center of the clutch into the engine.

You can make or use you own tool to hold the clitch dead center as long as its a good fit and about the same size as the spline, so once you have the new clutch in and the pressure plate loosely bolted on you can still move the clutch around behind the pressure plate now right in the center their is a hole in the pressure plate and the clutch plate this is where the tool needs to be put so that the clutch plate remains dead center whilst you tighten the pressure plate up this will then make sure that the spline on the gearbox lines up properly not doing this will make it impossible to get the gearbox on properly.

Let me know how you get on or if you need further assistance ok

Nov 07, 2009 | 1995 Nissan Pathfinder

2 Answers

Refill gearbox oil landcruiser hj75 1985?


Look on either side of the gear box and about half way up you will see a big bolt head.remove it and pump oil in it till it starts running out then you know its full to the right capacity

Aug 02, 2009 | 1985 Toyota Land Cruiser

1 Answer

1986 toyota landcruiser - auto box - quick chance setup kit for valve plate


Fitting an overdrive auto or a 5speed manual transmission will give a little more top end ......or..... fit larger tyres. V8 should have enough torque to cope well at lower speeds.

Jul 16, 2008 | 1986 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...