Question about 2002 Hyundai Santa Fe

1 Answer

Lights that show the gear position on the between seats console are not working. Where should I look first.

The lights that show the gear position on the console are not working. Is this likely a fuse and if so where is it.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 33 Answers

Bulb is probably blown pull cover off and and check bulb.is it a floor shift or colum shifter?

Posted on Apr 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where can I buy light for Chevy cobalt gear shift console


Most console bulbs are 194. Napa or any parts store.

Apr 14, 2015 | 2008 Chevrolet Cobalt

2 Answers

How do I release a stuck new seat belt retractor?


You are probably pulling belt at the wrong angle and it won't release. Pull with easy steady tension, trying a different angles and it should come free for you. If it doesn't, then take it back to SEAT or VW, they can show you in 1 minute how to free it. Since it's a mandatory safety device, there should be no charge unless it requires replacement.

Apr 04, 2015 | Seat Cars & Trucks

1 Answer

Cant locate on my 1998 dodge ram 1500 back up switch


Some cars,MBnz,have it where the gear selector connects to (under console where gearshift goes). I'd go to the dealer and ask parts' man to show you it then you may see how it works.. Some cars have it where the reverse position of the gear shaft,on transmission,makes contact to the reverse light switch. I'd start with dealer parts' man. Hope this helps. Alberto

Jan 31, 2014 | Cars & Trucks

1 Answer

I have a 99 Silverado and the passenger side seat back will not lock back into the upright position. Locks fine into reclining positions. What could be the problem?


i had this problem on my 96 chevy, basically theres a set of ratcheting gears that lock the seat in place in the various positions. sometimes over time or due to abuse one side or the other gets stripped out and the seat will no longer lock into place. i found a ripped up seat on Craigslist that was in a part out truck and bought it cheap then took both seats in the an upholstery shop, between the junked out seat (15 bucks) and the labor at the shop (50bucks) it cost me 65 bucks to fix, hope this helps

Mar 13, 2012 | 1999 Chevrolet Silverado 1500

2 Answers

I am trying to replace the console light on my 2006 pt cruiser and i am having trouble lifting it off and over the hand brake handle and shift lever.. it binds on both seats as i lift it up. do i have...


Turn the key on, move the gear shifter into low position, lift console slightly the reach your hand under the console and pull on the e-brake handle until you are able to lift off console.

Feb 06, 2011 | 2001 Chrysler PT Cruiser

1 Answer

Are shift settings supposed to light up? Is it a


Yes, they are supposed to light up. I believe that's on the same fuse as the instrument cluster, so if that lights up don't worry about the fuse. It's probably just a burnt out bulb. To replace, remove the knob - 2 screws, one in the front one on the rh side lift up, use thread lock to install, remove the floor console - seats forward remove one screw each side in the back, pull up to remove the parking brake console, seats rearward remove 2 screws from shift console, 2 pushpins each side, remove cupholders, lift and remove console. four screws to remove dial bezel then you'll see the connector for the lamp (the parking brake handle and gear selector will have to be moved to different positions to move console)

Aug 17, 2009 | 2001 Ford Escort ZX2

1 Answer

How can I remove gear shift knob on a 2003 Navigator?


it looks like you disconnect the shift cable and remove the center console finish panel with the shifter.


SECTION 501-12: Instrument Panel and Console 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Floor Console —Front, Navigator Removal and Installation
  1. Apply the parking brake.
  1. Position the front seat forward.
  1. Remove the two front floor console rear bolts.
  1. Position the front seats rearward.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the pin-typ retainer and the window control switch panel.
    • Disconnect the electrical connectors.
  1. Move the shift lever to NEUTRAL and position the shift indicator bezel aside.
  1. Remove the screws and the center console finish panel.
    • Disconnect the electrical connectors.
  1. Disconnect the shift cable.
  1. Disconnect the front floor console electrical connectors.
    1. Loosen the electrical connector bolt.
    1. Disconnect the connector.
    1. Disconnect the electrical connector.
  1. Remove the front floor console side finish panel.
    • If equipped, disconnect the electrical connector.
  1. Remove the front floor console front bolts.
  1. Remove the floor console.

Apr 17, 2009 | 2003 Lincoln Navigator

1 Answer

How to replace light in floor console that indicates gear selected


first i would check your fuses to make sure you havent blown one

Feb 08, 2018 | 2002 Honda Civic

1 Answer

No dash lights, power seats or windows. alternator not charging. Engine runs


  1. It might be that when you changer the battery post you might not have connected all of the leads on the positive post. You might also check for blown circit breakers caused while changing the terminals.Try using a dc tester and search the main breakers for power. If you have the manual it shows the breakers and links in the bulb replacement section. JOHN-LA.

Aug 31, 2008 | 1995 Lexus GS 300

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

Related Topics:

1,254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...