Question about 2000 Jeep Grand Cherokee

1 Answer

Ac blower won't work. Resistor has been replaced 3 times. I think it is the problem now. Is it easy to replace? Where is it?

Where is the blower motor resistor for the ac. Is it hard to replace? 2000 jeep grand cherokee

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 710 Answers

Blower motor resistors are found on the pasenger side ducts near the blower motor. It should have three wires going to it.

Posted on Apr 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I troubleshoot BMW 325i heat/ac blower? It suddenly stopped working.


REPLACE THE FINAL RESISTOR PACK, THEY GO OUT ALL THE TIME.

Sep 19, 2014 | BMW 325i Cars & Trucks

1 Answer

Where is havc resistor located


Try the blower motor resistor. It can be found behind the glove box. It costs about $20 and is very easy to replace (2 screws I think). If not that, try replacing the temperature control module ($30 used, $300 new). I'd start with the cheap and easy fixes (blower motor resistor) and work my way up to the more expensive fixes such as the module or blower itself. Good luck.

Jul 14, 2014 | 2005 Chrysler Town & Country

2 Answers

Heater won 39 t blow on 5


haw i fix my rpm meter problem

Sep 28, 2013 | Cars & Trucks

1 Answer

Air condition and heat won't work


Check to see if you are getting voltage to the blower motor if you are the motor is bad if not check the fan speed switch. 1 2 3 or low medium high if you get voltage going to the switch but not from replace the switch if you have voltage from switch check the blower motor resistor the although with the blower resistor you commonly have a high fan speed in the max setting and the lower speed settings don't work wich would make you think 1 2 3 are not working but 4 is. That is why it is best to check all parts to make sure the part you do replace needed to be replaced

Oct 15, 2012 | 2000 Ford Focus

1 Answer

Chevy s10


With the blower speed set to high and the key on tap the blower motor with the handle end of a large screw driver. If the blower starts to work than replace it.

If it still won't work check for power on the purple wire (i think its purple) and make sure the ground is good. If those two check out fine replace the blower motor.

If there is no power than you will need to check fuses and/or the blower motor resistor.

Jul 26, 2012 | 1997 Chevrolet S-10 Pickup

1 Answer

On my 2005 chevy suburban the front blower fan stopped working. The fuse tested good. It is either the blower fan or wiring assembly right ? Is there an easy way to test either ?


check the resistor i think it's a 7 way connector located by the blower motor i have had were the connector has melted to the resistor if this is the case you will need to replace both resistor and connector
the connector is available at a GM dealer or a AC DELCO parts dealer not sure about aftermarket
hope this helps

Dec 19, 2009 | 2005 Chevrolet Suburban

1 Answer

2005 malibu - heat/ac has 4 levels for fsn, level


Your blower speed resistor has gone bad and needs to be replaced. You can pick one up at Auto Zone or Parts Source with the step by step instructions to getting the resistor replaced with common tools.

It is located under the glove box, way in the back of the passenger foot area. You'll need to remove 2 screws with a 7mm socket, and remove the plastic cover that covers the blower motor and another component box that I think controls the passenger airbag. After removing the plastic cover you'll need to side that passenger airbag module to the right so it pop off its mounting bracket and move it out of the way. That will give a better view of the blower motor. I highly recommend you also remove the blower motor itself because the Blower Motor Resistor is located behind it. I think you'll need a 5mm or 5.5mm socket to remove the 3 screws that hold in place the blower motor and 2 more screws for the Blower Motor Resistor... It's a cramped location to work in but if you have all the tools and enough lighting then it shouldn't take more than 30-60 minutes to do. The Blower Motor Resistor costs about $19-$25. Good luck

Nov 30, 2009 | 2005 Chevrolet Malibu

3 Answers

AC & Heater Fan on fast spped only


Most of the time this is a bad "blower motor resistor". It is easy to replace. You will find your behind the glove box in the ac/heater (evaporator) housing. Below is a pic of the resistor as it is seen from behind the glove box. 1. resistor assembly. 2. harness 3. fasteners (2). 4. lower edge of glove box. (open).

f527558.gif

Jun 11, 2009 | 2002 Chrysler Town & Country

2 Answers

Fan control for the heater does not work.


I had the same symptoms on my Silo. I replaced the blower resistor (30$ or so) in about an hour. It is loacated in an awkward place in the footwell of the front passenger side. The blower resistor circuitpack is mounted in the blower body using three screws. The front two are easy to take off, while the third took me some time due to it being in the back and not easy to see. There is a cable harness/connector that you just unplug and later reconnect, after putting in the part. The original resistor I had was poorely designed such that the PCB trace is used as a resistance while not being well protected from the humidity caused by the AC and heating system. Few years back I had taken it off when only 1 nad 2 did not work, and had repaired the traces myself. Few years later I had to do the replacement because 3 4 and 5 went... The new part seems to be better protected so I hope it will last longer.

Mar 23, 2009 | 2002 Oldsmobile Silhouette

2 Answers

Heater/air con fan speeds


it is probably the blower motor resistor board it is located behind the glove box on the heater case assenbly by two screws unplug remove and replace is an easy fix

Nov 08, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

832 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...