Question about 1988 Ford Mustang

1 Answer

I have a 1988 ford mustang 5.0 efi. I want to put an after market exhaust on it, How do I put my O2 sensors on it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,586 Answers

The O2 sensors are mounted into the headers. If by aftermarket exhaust you mean a cat-back exhaust system with midpipes and mufflers, then the O2 sensors are a non-issue - they won't be touched. If you are doing cat-back, headers, and maybe high-flow cats, the O2 sensors will just screw directly into the new headers - they'll be set up to receive them.

Posted on Apr 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There are 4 o2 sensors on the 2004, 3.9L V6 mustang. Where are the locations for wiring for them please?


There are 2 on each Bank or side of the Exhaust system. One in front of the converter and one after the converter. The one in front of the converter does the heavy lifting of providing output to PCM to regulate the air to fuel ratio via trims to the injectors. Since you have a V6 with 2 bank, you have 4 O2 sensors.

Mar 28, 2017 | 2004 Ford Mustang

1 Answer

Code 42 ego always rich what is ego


Exhaust Gas Oxygen or otherwise known as the O2 sensor ford used this term up until 1994 when the federal regulations mandated industry standard terms and the implementation of the enhanced computer diagnostic system known as OBDII your O2 sensor is staying above .5v more than it should could be running rich,fouled plugs, plug wires excess fuel or a bad o2 sensor

Dec 07, 2012 | 1988 Ford F 150

1 Answer

98 mustang gt O2 Scensor location


Hi, the O2 sensors are located on your exhaust mid-pipe all the way forward near where it attaches to your headers. If you have a factory catalytic h-pipe, they are located forward of the two forward-most cats. I have a Magnaflow catalytic x-pipe on my daily driver, so I only have two cats and the O2 sensors are super easy to get to.

Jul 22, 2011 | 1998 Ford Mustang

1 Answer

1988 ford ranger idles runs rough. turn truck off and back on while driving and it clears the problem for about a minute if all the way


You may have a defective O2 sensor or a problem that is causing an O2 sensor to read either too much or too little oxygen in the exhaust. You should have it checked for an emission problem with your local professional automotive repair facility.

Apr 27, 2010 | 1988 Ford Ranger

2 Answers

Where do i find the O2 sensor on a 1998 ford f-150 4.6lt truck


1998 Ford Truck F150 1/2 ton P/U 4WD 5.4L EFI 8cyl
The Oxygen Sensor is located under vehicle, passenger side, below seating area, rear of catalytic converter, mounted in exhaust pipe.

Application: Number three

Hope helps (rated this) Good luck.


Jan 12, 2010 | Ford F-150 Cars & Trucks

2 Answers

I keep blowing EFI fuses on my Toyota pickup v6 4WD.


i have had this same problem.. check the exhaust pipe near the middle of the truck.. the o2 sensor was hanging down and would blow the efi fuse when the exhaust got hot.. took me months to find it..lol

Mar 28, 2009 | 1990 Toyota Pickup

2 Answers

1988 mustang rough idle its fine nwhen its cold then when it warms up it gets erratic


check plugs .rotor arm .distibuter cap .or check for dirty fuel filter

Feb 24, 2009 | 1992 Ford Mustang

2 Answers

2002 ford mustang gt map sensor enhancer connection? (for HHO)


MAP enhancers usually wont do the trick for long - the computer will learn the adjustment to the MAF and overide within a day or so usually less than a few minutes.

The computer is best altered using an EFIE to adjust the O2 sensor(s), usually adding between .2 and .3 volts to the O2 sensor signals does the trick - each combo of the HHO and car is slightly different - you have to play with it to find your best setting. You only need to alter the signal on the O2 sensors ahead of the cats as they are the ones the computer uses to adjust the fuel.

Aug 12, 2008 | 2002 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...