Question about 1991 Chevrolet Caprice

2 Answers

Injectors will not spray

My injectors are not opening i have changed the injectors and the ign madlue. pluse the fuel pump and relay the fuse and the fuses on the iner door jam. fuel is making it up to the injectors but it just will not come out and i got a new ecm put in it to. do eney no what the heck is going on. on the pressure is good all the way up to the injectors

Posted by on

  • 4 more comments 
  • keith tucker
    keith tucker Apr 22, 2009

    i just buy this ecm monday and it work find in my friend 91 caprice but when i put it in mine nothing. so i took it back got a nother one a still nothing o and what fuse is it my friend

  • keith tucker
    keith tucker Apr 22, 2009

    no i dont but i did check the voltage i hock a wire to the - part of the injector to the frame and the + side of the injector to this voltage reader i have and it get power like that. but if i hock up both of the wires to the injector wires from the reader nothing. do i have a bad grond or is it somthing elsa

  • keith tucker
    keith tucker Apr 23, 2009

    witch prom is it do in the computer i have one hole bundole of wires going to the ecm and when i look in side the ecm the all prom are all there but is that why i dont get a pulse or somthing.

  • keith tucker
    keith tucker Apr 23, 2009

    do u know were i can get a diagram from for the injector wires and i may go get some more injectors i got them from the junk yard you know good but low cost place to go

  • keith tucker
    keith tucker Apr 24, 2009

    ok here is a nother problem how the hell i lower the pressure to my injectors i keep blowing the injector mount the shell that holds the two injectors in it.or the pressure is just to great and the injectors not openen so its just blowing that up. and how do you get water out the engine. that was the problem do thank the computer chip in side it. thank you

  • Anonymous May 10, 2009

    no pulse to injectors for a 92 caprice I have changed fuel pump relays, fuel pump, injector connectors, rebuilt pressure regulator, tested with noid light no pulse, changed distribitor three times, i'm lost did you fix your problem

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

There is a fuse for the injectors check voltage at the injector it should read battery voltage.or your prom is bad in the computer.

Posted on Apr 21, 2009

  • 2 more comments 
  • mike loshbough
    mike loshbough Apr 22, 2009

    due you have a test light if so turn key on and start checking them .also check for voltage at the injector.

  • mike loshbough
    mike loshbough Apr 22, 2009

    you should have power then ground is supplied by your quad driver in the computer.you may have wiring issues!

  • mike loshbough
    mike loshbough Apr 22, 2009

    did you change the prom in the computer or take it out of the old one?

  • mike loshbough
    mike loshbough Apr 23, 2009

    try autozone for the wiring diagram. the prom is a chip under the cover of the computer.it does not come with a new computer.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the wire from ecm to injectors for sure burnt from the exehust line you will found a hidden burn cut

Posted on Mar 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 pt cruiser keeps blowing fuel pump fuse,replaced fuel pump, no change.runs rough at idle and stalls,blows fp fuse,also replaced ign.coil,plug wires and plugs also changed relays


There are two fuses for the fuel pump relay. One fuse is load side of relay, that fuse also sends voltage to load side of asd relay, the asd relay sends voltage to several systems, two of which are the fuel injectors and ignition coil. I'm not telling you to replace, anything, but, you need to do some testing.
The other fuse goes to control side of relay, smaller amp fuse. I don't know the amp rating of the fuse that keeps blowing.
See that fuse, it supplies voltage to load side of fuel pump relay and also to asd relay.
26322929-c15bjyrfwzlf33vqjpu1ik1c-2-0.jpg

Oct 22, 2016 | 2004 Chrysler PT Cruiser

1 Answer

WHEN I TURN ON THE IGN SWITCH TO START POSITION I KEEP BLOWING THE FUEL PUMP FUSE BUT WHEN I REMOVE THE INJECTOR RELAY IT DONT BLOW THE FUSE


I would think that either the power wire feeding the pump or the pump itself is grounded and causing the fuse to blow. Pulling the injector relay is opening the circuit and not feeding power to the pump would be why it doesn't blow the fuse when it is removed.

Aug 12, 2015 | 1999 Mazda 626

2 Answers

Fuel injectors not spraying


Bad fuel pump or relay to fuel pump or blown fuse to Main Relay or bad relay, could cause no spray from injectors.
Hope this helps.

Apr 02, 2015 | 2012 Mazda 6 i Sport Sedan 2.5L 4-cyl....

1 Answer

Fuel injectors activated by fuel pump relay? 92 BMW 525!


The injectors have constant voltage to them with key on. It is a fused circuit. The computer internally grounds the injector ground wire to cause injector circuit on- to pulse the injector, and fuel is then sprayed out. It is a separate circuit from the pump circuit.

Jan 06, 2014 | 1992 BMW 5 Series

1 Answer

No pulse to injectors


I have no injector pluse on a 1994 vin. z T B I plus fuel pump don,t run quit driven down road it,s a 4.3 engine changed colmude,pick-up coil,fuel pump will start on spray

Jan 03, 2014 | Cars & Trucks

2 Answers

I have a 1999 chevy blazer that will turn over but won't start. prime with fuel runs untill it runs out. have code of p1351 in it


Need more info.......It could be the injectors are not pulsating...Check to see if it is spraying fuel from the injectors....If not it should be a clogged fuel filter or a fuel pump....It is almost definite though that it is the fuel pump/sending unit in the tank ...IF it is not spraying from injectors....
Disconnect battery remove main fuel line going in the fuel filter under vehicle frame at drivers side..with drain pan under it of course...Reconnect battery turn engine over and watch for fuel...
You will need an assistant...Most people think fuel is under great pressure but it is not.....If everything works the fuel will come out in a stream...But it wont come out like a bullet...
If fuel comes out Fuel pump in tank is good...Then your problem is at the injectors ...I would change the filter of course anyway...unless you just have...You will see rusty dirt come out of it if it is clogged...It is always good to change fuel filter every 15,ooo....Todays fuel is terrible...I would first check or swap fuel relay with a new relay or identical relay in fuse power block ...Make sure they are all good....................What engine and how many miles ? Hope this helps....Metalpoet

Apr 17, 2011 | Chevrolet Blazer Cars & Trucks

6 Answers

90 chevy 350 with TBI starts but wont stay running changed fuel filter and fuel regulator dont know what next


I have a 90 chevy k1500 350 tbi with same problem! I have traced problem to... after turning on key fuel pump kicks on when u crank it over injectors shoot gas and truck starts! After few seconds injectors stop spraying and truck dies! This can happen many times over and over! Eventually sometimes truck stays running and all is great! I changed ignition module, oil pressure sending unit (which i was told controls gas after vehicle is running) fuel filter, computer, fuel pump relay, I am at a loss now! Hope this helps and hope someone can help me!

Aug 10, 2009 | Chevrolet C1500 Cars & Trucks

3 Answers

1986 BMW 318i;Turns over but engine wont run.I'm


Fuel pump may be getting weak. If pressure is not high enough the injectors wont open.

Jun 27, 2009 | 1986 BMW 3 Series

2 Answers

Volvo 240 2.3L FI the engine has spark, no injector pluse.


is there air in the fuel rail? bleed air bubble out

Mar 15, 2009 | 1989 Volvo 760

Not finding what you are looking for?
1991 Chevrolet Caprice Logo

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...