Question about 2005 Hyundai Sonata

1 Answer

Engine light came on and car was stalling and get code p0335 but now running ok

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

You need to have your crank sensor replaced!

Posted on Jun 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0335 P0300 - 4 cyl


Question: where did you buy the new crank position sensor? I had the exact same problem with my 2004 Nissan Altima and bought new crank position sensor from one of the auto parts store. Put it in and same problem. I was baffled. Finally decided to get the crank position sensor directly from the dealer. Fixed the problem. This was my experience, not sure if your case will be the same.

Dec 13, 2013 | 2002 Mitsubishi Galant

1 Answer

Stall Driving, Crank and no start codes p0127 p0335 p0340


it is in your firing distribution and or ignition coil pack on any engine when you get these codes ..if the vehicle is showing codes and it is still running say smooth ,,it will not be for long ,,those lights come on generally before these components go out

Oct 18, 2013 | 2004 Toyota Tundra

1 Answer

Dodge intrepid 2004 showing code p1687, check engine came on and air bag light, speed ometer and tack gauge dropped to zero but started working 5 seconds later light is still on and showing this code. Can...


the lamps all change at engine stall , did it stall.
at about 300 rpm all engines (gas) stall, and the ECU changes state.
all cars.
does car run, ok, drive ok ,start ok, and sound ok? just a clue here.

Sep 25, 2013 | 2004 Jeep Wrangler

1 Answer

P0335 code car shuts off when driving?


P0335 stands for Crankshaft Position Sensor Malfunction change the sensor and the car should run great but in order to remove the check engine light you have to hook it up to a scann tool and press erase codes

Nov 20, 2012 | 2006 Hummer H3

1 Answer

Check engine light is on in my 2005 altima 2.5 got it scanned and the codes i got were P0335 /P0725/P0420 also car keeps stalling


po335 and 725 bad crank sensor and this is also reason for stalling.po 420 catalyst has lost efficiency....needs new catalytic converter ...covered under 8year 80000 mile emmisions warranty.

Feb 08, 2011 | 2005 Nissan Altima

2 Answers

02' Nissan Altima, car jerking, turns off at light, but turns right back on. Engine light on, code from autozone P0335 crankshaft position sensor. P0725 Engine speed signal circuit. The start up, days it...


If it has a code for loosing the crankshaft position sensor signal, I would certainly start looking at that before venturing into the fuel system. Cam and Crank sensors are a common failure item for Nissans of that era. Nissan actually redesigned the sensor and i think they performed a recall on some vehicles. They are fairly inexpensive and easy to replace. I believe they run about $40 each. Because most people don't have access to a powerful scanner or a digital storage oscilloscope to verify the failure I recommend replacing the cam and crank sensors at the same time.

Sep 02, 2010 | 2002 Nissan Altima

2 Answers

I have a 2003 Nissan Sentra SE-R and the engine keeps sputtering while i am driving and the diagnostic pulled the P0335 code indicating that my CKP is malfunctioning but i just replaced it and it is doing...


Note - not a solution..just adding my woes!
I drive a 2003 Nissan Sentra SE-R Spec V.
My car suddenly stalled 1 day and the engine wouldn\'t turn over. Brought it to my mechanic and had the Camshaft position sensor replaced by my mechanic. The car ran fine for about 2 weeks and then the light was back on with the initial symptoms.

Took the car into the dealership and they diagnosed it again as P0335. Said that the mechanic hadn\'t installed the sensor correctly. Charged me a bunch of money to replace the thing and not too long ago the check engine light is on. The Revs bounce around everywhere. Checked the code again and it\'s P0335 yet again! Am in talks with the dealership to get to the bottom of this...

Apr 19, 2010 | 2003 Nissan Sentra

1 Answer

What do codes p0335 and p0341 mean on 1996 Cavalier?


when your engine went into that 5 second sputter,
your computer or "PCM" did not get a constant signal from the crank or cam sensors that the engine was running.
These two sensors tell the computer what RPM the engine is turning so it can adjust fuel and spark.

Nov 21, 2009 | 1996 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

392 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...