Question about 1993 Toyota Celica

1 Answer

93 celica st were to find these parts??

I have a 93 celica st. i got into a fender bender i guess you could say i need to replace the front hood, passanger turn signal , front support bar that hold the hood down, were can i find these parts for cheap !?? PLEAE HELP ME : (

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Call around to your local junk/recycling/wrecking yard... some specialize in imports

Posted on Apr 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Chevy Aveo in Minor fender bender now won't start


Minor fender bender ? Where , front , rear etc.... Could have damaged wiring harness , sometimes GM mounts the PCM - engine computer behind fenders , body parts etc...

Oct 17, 2016 | 2004 Chevrolet Aveo

2 Answers

93 toyota celica gt. Engine turns over but wont spark.plugs new wires and cap and rotor good put ohms meter on coil and secondary output and is in specified range but have no power to coil.changed ignitor...


I'm going to guess TIMING BELT. Fairly common with this engine. Thankfully, they are a "NON-interference" motor so it didn't do any damage when the belt snapped. Just need to replace it. Should cost around $300-$400 depending on where you are. Good luck!

May 09, 2010 | 1993 Toyota Celica

1 Answer

A minor fender bender knocked the pass side frt flare and fender splash guard off shearing all the fasteners. What do I need in order to re-fit them? Later, I will need to replace the front bumper cover -...


Any auto parts store will have those fasteners.Most just push in(one time use only)and others are two piece and can be used over and over.You will need to know the size of the hole where the fasteners lock into.

Jan 20, 2010 | 2003 Jeep Liberty

1 Answer

Front fenders need to be removed


take the inner fender well out, unbolt the fender from the bumper, take the 2 bolts out under the car at the fender, lastly take all the bolts along the fender out, and gently pry it loose

Aug 07, 2009 | 2000 Toyota Celica

1 Answer

How to set a timing belt


Factory timing for all 90-93 normally aspirated Celicas (ST, GT, and GT-S) is 10º before top dead center (BTDC). This means when the crankshaft angle of the number one cylinder reaches 10º, the spark plug will fire. It fires before it reaches top dead center (TDC) because the flame front takes time to fully combust and push the piston downward. this site might help u .http://www.toyotacelicaonline.com/timing.htm

Jun 09, 2009 | 1995 Mazda 626

1 Answer

Hood, Front/Rear Bumper replacement


collisionrepairadvice.com  you can most likely find the parts at the local junk yard.  Yes with some skill and tools you can do these repairs yourself...Good luck

Mar 26, 2009 | 2005 Honda Accord

1 Answer

2000explorer hood release


sit on hood or pound on it (center front) while assistant pulls cable release from inside..then adjust stops so it wont happen again...have you had a fender bender recently?

Oct 17, 2008 | 2000 Ford Explorer

1 Answer

I have a 93 escort wagon , that i love... it was hit in an accident... i bought a liitle parts car an need to replace parts.... does anyone have auto body part on the manuel?


I have done this for years and am familiar with these cars. The first thing to do is cut in your parts, by that I mean paint the inside edges of your door, fender and hood before you install them. The hood is a no brainer. four bolts probably ten millimeter. The fender is not very hard either, remove headlight and side marker and front bumper. The door needs to be disconnected under the dash and the wires pulled out before removal. Install the door and adjust it till it fits and closes properly, then the fender by lining up the body line before tightning into place. Before putting in the bolts along the top install your hood and align it with the back of the cowl so that it is even gap all the way across then adjust fender gap and tighten down. This will work perfect if your inner structure has not been bent or knocked over. Be glad to help further if you need it

Aug 29, 2008 | 1993 Ford Escort 4 Door

1 Answer

89 celica fenders, front; will fenders from a coupe fit the converible


Only 87 -89 convertible fenders will work on the convertibles.

Jun 27, 2008 | 1989 Toyota Celica Liftback

Not finding what you are looking for?
1993 Toyota Celica Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...