Question about 2002 Nissan Sentra

1 Answer

Does hub need replacing when replacing a wheel bearing

Nissan sentra 2002

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Nissan Master
  • 383 Answers

Rdfairfield: if you are asking about the rear? Yes, that is the only way the part comes and is manufactured. It is a hub and bearing assembly..

Posted on May 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2011 Nissan Sentra. It has developed a loud hum and vibration to the steering wheel from the front end .it has 180,000km. Any ideas?


How are the tires? New? Old? Rotate them and see if noise goes away. Possibly front wheel bearing in the front drive axle where it goes thru the hub and rotor.......goes the noise get worse if you turn right or left slightly when driving it? If it gets worse on one side that is the side with the bad bearing.....replace as needed.

Aug 31, 2014 | 2011 Nissan Sentra 2.0

2 Answers

Procerure to replace wheel bearing assy 2004 nissan altima 4cyl


Go to YOU TUBE and put in replacing wheel bearing hubs for
nissan altima & watch

There is a lot to see even if on a different vehicle

I doubt you have the tools to do the job

Sep 19, 2012 | Nissan Altima Cars & Trucks

1 Answer

Front wheel bearing instalation


Engage the emergency brake. Place the socket end of the tire wrench over the lug nuts and turn 45 degrees to break the nuts loose. Do not unseat the wheel from the wheel hub.
  • 2Jack the Sentra into the air using the factory front jack point. This is located behind the radiator.
  • Finish loosening the lug nuts and remove the wheel.
  • 4Unbolt the upper and lower caliper mounting bolts and lift the caliper off the brake rotor.
  • 5Secure the brake caliper to the coil springs above the brake system with zip ties.
  • 6Slide the brake rotor off the hub assembly.
  • 7Remove the bearing cap on your Sentra. To do this, you need to use channel locks. Grab the bearing cap with the end of the channel locks. Then, twist the channel locks back and forth. You will eventually be able to loosen the bearing cap so that you can pull it off.
  • 8Grab the end of the cotter pin on the spindle nut with pliers and pull it out of the nut. You may need to pull fairly hard, but the pin will come out.
  • 9Turn the spindle nut counterclockwise to remove the spindle nut.
  • 10Tap the wheel bearing out of place with a rubber mallet or a hammer.
  • 11Tap the bearing races out of the hub with a hammer and punch tool. You need to do this for both sides of the hub.
  • 12Clean the inside of the hub, the spindle, as well as the spindle nut brake parts cleaner and wipe them dry with a clean rag.
  • 13Install the new wheel bearing. Tap the new bearing into the hub using a rubber mallet. Make sure you are using a rubber mallet so that you do not damage the new bearing.
  • 14Reassemble the hub assembly, brake assembly, and put the wheel back on and tighten the lug nuts so that the wheel sits flush against the wheel hub. Installation is the reverse of removal.
  • 15Lower the Sentra to the ground and set the dial on a torque wrench to 100 lb-ft. Tighten the lug nuts clockwise until the wrench clicks. This will indicate that the proper torque value has been reached.
  • Jun 29, 2012 | 1997 Nissan Sentra

    1 Answer

    Wheel bearing on right front of 2002 nisan max come in hub/bearing as one unit or bearing come sepret and have to be pressed in hub thank you gene


    YEP WHEEL BEARINGS HAS BE PRESSED IN WITH A SHOP PRESS ALSO THE HUB HAS TO BE PRESSED INTO STEERING KNUCKLE.

    Jun 29, 2010 | 2002 Nissan Maxima

    1 Answer

    I have abroken wheel stud on a 2003 Nissan Sentra, how do remove the hub?


    did u know u should be able to pound out the stud and replace it?

    anyway.. remove tire, remove brake calliper, remove rotor, remove the cap in the middle of the wheel bearing (hub) and remove the big nut.

    there is 3 or 4 bolts behind the hub that hold the wheel bearing (hub) on, remove those. Get a hammer and a chisel and separate the wheel bearing from the rest of the housing.

    Apr 12, 2010 | 2003 Nissan Sentra

    1 Answer

    Step by step on how to replace front wheel bearing on 02 Nissan Sentra GXE


    Raise vehicle, remove wheel, remove brake caliper, remove brake rotor remove steering knuckle by disconnecting the tie rod, ball joint, and strut. press out hub, remove snap rings press out bearing. Reassemble in reverse order.

    Aug 01, 2009 | Nissan Sentra Cars & Trucks

    3 Answers

    How do you change rear wheel bearing on a 2004 nissan sentra


    Yes it is as easy as it looks. If you had the tire off and figured out that it looks easy, you shouldn't have much problem.

    Mar 21, 2009 | 2002 Nissan Sentra

    1 Answer

    Replace front wheel bearings


    The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
    Remove wheels and brake calipers
    If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

    On a scale of 1-10 difficulty, Id rate it a strong 7

    Jun 20, 2008 | 1998 Nissan Sentra

    2 Answers

    Nissan sentra gxe 03 rear wheel hub bearing problem


    Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

    Jun 12, 2008 | 2003 Nissan Sentra

    Not finding what you are looking for?
    2002 Nissan Sentra Logo

    231 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    705 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...