Question about 1998 Subaru Forester

1 Answer

Timing specs cannot figure out how to set timing

Posted by on

  • yadayada
    yadayada May 11, 2010

    timing is not adjustable, there is no spec.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 218 Answers

THE TIMING SHOULD BE 15 DEGREES BTDC +OR- 8 DEGREES.U CAN NOT ADJUST THE TIMING IF IT OUT OF SPEC. THEN U HAVE A TIMING BELT ISSUE OR A PROBLEM W/ THE IGNITION CONTROL SYSTEM.THE VEHICLE COMPUTER CONTROLS TIMING

Posted on May 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for the 5 bolts that secure the Transmission Manual Valve Position Pressure Switch


Torque specs on on 4L60 tranny pan in 04 escalade??

www.cadillacforums.com/.../cadillac-escalade.../260881-torque-specs-4l6...
May 26, 2012 - 3 posts - ‎3 authors Has 104000 miles on it now, figured it's time to change the filter and the fluid. ...Cadillac Escalade, EXT and ESV Forum - 1999 - 2006 Discussion, ... Flywheel toTorque Converter Bolt ... Transmission Fluid Pressure Manual Valve Position Switch to Valve Body Bolt ... Powered by vBulletin® Version 4.1.5 Re: SRX V8 Valve Cover Gasket Replacement Write Up ...
14 posts
Jun 10, 2015
2000 DTS Setting up Internal Mode Switch - 4T80E ...
9 posts
Aug 27, 2014
More results from www.cadillacforums.com

Nov 19, 2015 | 2000 Cadillac Escalade

1 Answer

93 e150 camshaft specs 5.8L


Factory camshaft specs:
5.8L (non lightning): Lift: .278" Intake; .283" exhaust.
5.8L Lightning: Lift .260" intake, .278" exhaust.
(No other specs given)

Base timing: 10* BTDC (Before Top Dead Center)

Apr 21, 2014 | Ford F-150 Cars & Trucks

1 Answer

How can I adjust time timing on 91 ford F150 5.8L


let the engine get to normal operating temperature, then pull the spout (spark plug out) connector. Then hook up your timing light and rotate the distributor until you're at the timing spec you're looking for. I believe 10* BTDC is the OEM spec for the 5.8. Once you've got your timing set, put the spout back in. and you're set!

Jan 07, 2012 | 1991 Ford F150

1 Answer

How do you set timing marks on 1999 Toyota Rav 4 ?


must have timing lite. Hook timing lite up to battery place spk lead to #1 cylinder remove cover from data link connector (rectangler box on fender well) lid of box has diagram of pins short pin TE1 to E1 loosen distributer and set timing to spec. Spec should be on emission lable under hood.

Jan 12, 2011 | 1999 Toyota RAV4

2 Answers

How do u set the timing on a 93 gmc sierra 1500 350 ?


You can set the timing but the ecm, engine control module will reset it back to specs. So it useless to try. Good luck dont forget to rate

Jan 07, 2010 | 1993 GMC Sierra K1500

1 Answer

1998 4cyl.camry had a stuck valae due to bad gas{varnish}. removed valve cover, got valve unstuck. had to remove exhaust cam, but not the intake cam. need to reinstall and time exhaust cam. can not...


simple to figure that out . the key ways are always up on camshafts. it allows for them not to fall out when assembling the engine . so use the balancer to determine tdc (top dead center on cyl one) and make sure both keys are straight up . (just loosen the cam retainer nuts and look to see what set of marks they line up with and dont forget t re-torque them to factory specs somewhere between 22 and 28 ft lbs but not a lot more) , google the specs up to be sure

Oct 29, 2009 | 1998 Toyota Camry

1 Answer

How to time a 1995 geo tracker


if u mean set the timing....u need the proper tools .....and specs ....and if you have changed timing belts or chains .....replacement procedure is very precise....;-)....but with proper timing light an specs setting timing is relatively easy........but in order to tell u i need to know what timing light ur using....

Sep 26, 2009 | 1995 Geo Tracker

1 Answer

I need to figure out how to set the timing on my 93 fullsize bronco. 5.0 with stock distributor


This should help even though its not a Mustang. Same motor and spec.

Jun 08, 2009 | 1993 Ford Bronco

1 Answer

Instructions for setting the time .1993 toyota pickup 3.0 v6 engine


Please send me your e-mail address; I will send you the complete timing proceedure; the file I have is a .pdf, and FixYa will not let me upload a .pdf to the FixYa site. I suspect that your cam timing is off on the passenger side of the engine. You want the specs for a 93 V6, correct?

Oct 08, 2008 | 1993 Toyota Pickup

Not finding what you are looking for?
1998 Subaru Forester Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...