Question about 2002 Audi A4

1 Answer

I need to replace the rear brakes and rotors on my 2004 Audi A4. Will I need special tools to do this? Can I still do the job without these tools?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 34 Answers

'B6' (2001-2004) A4s dont have seperate rotors on the rear brakes like the pre 2001 A4s do. When changing the rear pads + discs the only special tool you will need is a caliper wind back tool. Let me know if you do also need to replace any ABS components aswell as I might be able to advise.

Posted on Apr 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake pad replacement 2004 audi a4 and rotor how do i do and what tools are neccessary?


YOU NEED REMOVE A LITTLE BRAKE FLUID FROM MASTER CYLINDER.THEN YOU RAISE VECHICLE SAFELY.SUPPORT IT WITH JACK STAND.MAKE SURE VECHICLE IS ON LEVEL SOLID GROUND.REMOVE TIRE OR WHEEL.THEN YOU NEED A LARGE C - CLAMP.PLACE C - CLAMP OVER BRAKE CALIPER AND BRAKE SHOE BACKING.TIGHTEN C - CLAMP JUST ENOUGH PUSH CALIPER PISTON BACK IN CYLINDER BORE TO REMOVE CALIPERS FROM ROTORS.TO REMOVE BRAKE CALIPER YOU NEED 2 OPEN AND BOX END WRENCHES ONE TO HOLD CALIPER SLIDE PINS AND THE OTHER WRENCH FOR LOOSEN CALIPER BOLTS.THEN YOU REMOVE CALIPER AND REPLACE FRONT BRAKE SHOES.IF YOU NEED TO REMOVE BRAKE ROTORS JUST REMOVE THE BRAKE CALIPER CARRIER SUPPORT BOLTS THE REMOVE THE BRAKE CALIPER CARRIER SUPPORT THEN REMOVE ROTOR.YOU NEED TO REPLACE BOLTS WITH NEWS AND USE LOCK TIGHT.THEN YOU PUT IN NEW BRAKE PADS IN CALIPER PUT CALIPER BACK ON SUPPORT CARRIER.REPLACE WITH NEW BOLTS USE LOCK TIGHT THEN TORQUE BOLTS TO 26 FT LBS.MAKE SURE MASTER CYLINDER COVER IN PLACE.WHEN YOU FINISH REPLACING BOTH FRONT BRAKE PADS PUMP BRAKE PEDAL TO SEAT BRAKE SHOES AGAINST BRAKE ROTORS SO YOU WILL HAVE FIRM BRAKES WHEN YOU APPLY THEM. THEN CHECK YOUR BRAKE FLUID LEVEL IN MASTER CYLINDER MAKE SURE ITS NOT LOW. MAKE SURE YOU HAVE FIRM BRAKES BEFORE DRIVING.IF YOU HAVE ANY PROBLEMS CHANGING FRONT BRAKE PADS YOU CAN GO TO ANY AUTO PARTS STORE AND BUY A HAYNES REPAIR MANUAL.

Jun 16, 2010 | 2004 Audi A4

2 Answers

High speed braking steering wobble


your brake rotors are most likely warped. replace them maching them only makes the problem worst

May 12, 2010 | 2001 Audi A4

1 Answer

Hi need to change rear brake light on my 2002 audi a4


After removing screw,you need to prise unit off
Start from inside of unit untill it moves,then push to out side of car to release
The unit will be tight,as it probably has not been removed
The ideal tool to remove is a plastic trim removal tool
A screwdriver will do the job
Refitting,locate slots on out side of car,and push firmly in,replace screw

Apr 08, 2010 | 2002 Audi A4

1 Answer

What is needed to replace rear shocks in a 2000


This operation requires a coil spring compression tool as a special tool for replacing rear shocks after coil spring & shock assembly was removing out of the car.

Feb 23, 2010 | 2000 Audi A4

1 Answer

How to compress a audi a4 rear brake cilinder?


you need a special tool that turns and pushes the piston into the caliper. YOU CAN NOT just push it in you will damage the piston and not push it in.

Sep 14, 2009 | 2004 Audi A4

3 Answers

Audi a4 1.9tdi quattro front wheel bearing noisy


it would be best if you let a shop fix there are some special tools needed that the shops should have.

Sep 12, 2009 | 1998 Audi A4

2 Answers

Changing rear brakes 2005 freestar


The brake calipar pistons on the rear, have to be turned in with a special tool, they can't be pressed in like the front. turn them in just far enough for the new pads to fit over the rotors.

Jul 16, 2009 | 2006 Ford Freestar

1 Answer

2004 x3 rear brake pad replacement diy


You Can probably accomplish this yourself if you have a brake pad warning light or ABS/ASC light on you may need a BMW tech to reset the system to complete the job.

Jul 02, 2009 | 2004 BMW 3 Series

2 Answers

How to depress rear brake caliper piston on an 2004 Audi A4


It must be turned clockwise while being pushed in. The local parts store will have a tool just for this purpose.

Mar 27, 2009 | 2004 Audi A4

1 Answer

2004 Saturn Vue Brakes


The vibration is caused by the rotors being warped. Remove the front tires and check the front brake pads. Replace if needed. This is a pretty straight forward job. The rotors are "fall off" rotors and you won't need anything special tool wise.

Jun 12, 2008 | 2004 Saturn VUE

Not finding what you are looking for?
2002 Audi A4 Logo

1,053 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...