Question about 2002 Dodge Durango

1 Answer

Change front drive shaft - 2002 Dodge Durango

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

Simple swap. If beyond capability try a shop manual from chilton or haynes. Any parts house will have a shop manual

Posted on Apr 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is the front drive shaft spinning on 2003 lincoln aviator?


The car is a all wheel drive and in 2wd mode there is solenoid on the front axle shaft that keeps it disengaged so fuel mileage can be higher this is normal

Jul 18, 2014 | 2003 Lincoln Aviator

1 Answer

Changing front axle assembly or wheel hub or both? Either way, need torque specs for all bolts.


you've got a bad axle shaft in the front and possibly a bad bearing in the hub. 4/wheel drive makes the front axle actually work. Theys no real pressure on these shafts when in 2/wheel drive.

Feb 01, 2013 | 2002 Chevrolet Silverado 1500

1 Answer

How dificult is it to change drive shaft universal joints myself on my ford focus 1998 5 door hatch


You have front wheel drive & CV Joints,
not U-Joints ,is that not correct

CV Drive Axles in front wheel drive vehicles
are just replaced as a complete axle assy

Jan 29, 2013 | 2008 Ford Fiesta 1.4

3 Answers

Need to know steps involved to disconnect transfer case from transmission so that I can still drive my Yukon


best bet is junkyard replacement. worst case. remove tc and get a longer driveshaft to the rear end

Jun 29, 2017 | 2001 GMC Yukon

3 Answers

Is there a drive shaft


no, there is no "drive shaft" on a 94 oldsmobile. It is front wheel drive. you have a CV shaft from trans to left front wheel and a separate CV shaft from trans to right front wheel.

Jan 14, 2011 | 1994 Oldsmobile Cutlass Ciera

1 Answer

My vehicle vibration while running.we change all tyres and wheel rims. front and rear propeller shafts,check wheel hub run out.check and adjust alignment but problem same.


Front and rear impeller shafts?? Not sure if you mean drive shafts or not? The problem could be in your front drive axles/drive shaft. If you replaced them all that would be 4 total (very expensive). I would try another shop if that much was replaced and didn't solve the issue. When does the problem start in idle, driving on bumps, highway? Could be a motor problem too. Need more info.

Oct 02, 2009 | Lexus LX 570 Cars & Trucks

1 Answer

Want to change to rwd


Front drive could (theoretically) be disconnected by removing the front half-shafts, blocking the shaft exit points and welding the bevel gears in the center differential. Wouldn't want to try that, though...

Sep 20, 2009 | 1990 Toyota Celica

1 Answer

How to replace front drive shaft ?


Mark the drive shaft postion to the transfer case and front axle. Remove the bolts/straps from the transfer case and front axle pinion that hold the drive shaft in place. Remove drive shaft. You may have to drop the exhaust pipe for access.

Jun 02, 2009 | 1997 Dodge Dakota

1 Answer

Rattling sound in drive shaft for 2003 GMC Sierra


Not sure what  you mean by rattling. If it is your drive shaft it could only be a worn U joint os just change the front and rear U joint unless you bent the drive shaft, but the shop should be able to tell you. The only other thing that would rattle under the truck would be the heat sheild for the Catalytic converter and muffler. Good luck and hope this helps

Apr 08, 2009 | 2003 GMC Sierra 1500

Not finding what you are looking for?
2002 Dodge Durango Logo

Related Topics:

472 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...