Question about 2004 GMC Envoy

1 Answer

O4 envoy need to replace axel shaft seal front drivers side how does the axel shaft come out is it holding on by c clip around the end of the shaft how does that come out w a block o wood and hammer?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

Yes it just pops in and out a block and hammer should do it
its a tight fit!!!

Posted on Apr 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have gear oil leaks under transmission in two holes next where the axel meets on each side


Keith the seals will need replaced, take into a shop and have a tech give estimate for repair. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
half shaft seal replacement Google Search
How To Install Replace Front CV Axle Shaft 2002 09 GMC Envoy and XL XUV
Part 1 How To Replace Front Axle Shaft Seal RH Front Chevy GMC
CV axle replacement Subaru Outback 2000 Legacy Forester Install Remove...


May 04, 2016 | Cars & Trucks

1 Answer

How to replace bearing in a 1991 chevy 1500 4x4 rear axel at driveshaft?


To replace pinon bearing you need to pull wheels and the brake drums off next pull cover off the back of the rear end (make sure you have a drain pan under rear end) next turn dive shaft till you see a small bolt remove bolt pull center pin out push axle in pull c clips out pull axels out remove four bolts holding ring and spider gears remove gears assembly next remove drive shaft remove bolt from pinon push pinon in remove seal and bearing

Jun 27, 2011 | 1991 Chevrolet K1500

1 Answer

When changing out the right axel should the axel pull out of the transmison or is there a lock of some sort that will need to be removed.


The shaft has a clip on the end to hold it in the transmission but it stays with the shaft and does not need to be removed seperately, Easiest way to get the shaft out is to use 2 prybars, on on each side and pop the shaft out. When installing the new shaft, make sure it is in all the way and that the clip is holding it in.

Feb 26, 2011 | 2000 Hyundai Sonata

1 Answer

How to replace a front driver side axel for a 2004 toyota corolla


remove wheel
remove large nut in center of hub
unbolt lower control arm allowing the assembly to "swing" out a bit.
with a prybar, you will have to snap the shaft out on the transmission side to disengage the clip holding the shaft in.

Nov 09, 2010 | 2004 Toyota Corolla

1 Answer

1993 Jeep Wrangler - Front Axel U joint, why no C clips?


The factory u-joints use plastic injection for retainers so when it comes time to replace the factory u-joint use a torch to heat the u-joint cups and you will see a melted plastic worm come out the side of the drive shaft, now you can drive out the old joint.
The replacement joint will use inner c-clips.

Jul 19, 2009 | 1994 Jeep Wrangler

1 Answer

1999 dodge cummins 2500 front axel seals


you need to pull off wheels,brakes, rotor /unit hub bearing, both axles and intermediate shaft, as well as the vac disconnec ton the front axle tube. if only the right side leaks then only then only pull the right axle and intermediate shaft and vac disco. it is a trick with a miller tool to replace the seal. the left side seal is inside the diff and the carrier has to come out to replace it. pete

Jun 09, 2009 | 2004 Dodge Ram 2500

1 Answer

Rear Axel Seal


Wheel, brakes etc that are in way of pulling axle out have to come off. Drain rear end fluid, remove rear housing cover, remove bolt that holds pin in differential, remove differential pin, push in slightly on axle to remove "U" clip that holds shaft in, then slide shaft out. replace seal. Reverse procedure for re-install & fill with gear lube. If any questions, get back to us.

Apr 16, 2009 | 2002 Ford Mustang

2 Answers

1994 toyota 4runner front diff.seal replacement on passenger side


it should be the exact same process just with a little longer axel shaft

Jan 11, 2009 | 1984 Toyota 4Runner

1 Answer

LEAKING FRONT AXIL SEAL


take the wheel off , unbolt caliper and sling it out of the way with a bungi cord, take off the rotor, then you have too take the pumpkin cover off the axel diff in the front (drain fluid first) easy way to do that take out bottom and side bolts out then leave top 1 or 2 in but finger loose. pry cover off with a sturdy scrapper from side allowing fluid to leak out from bottom of cover. when fluid is done comeing out then take off cover. to take the axel out to replace the seal you have to push the axel inwards to remove the C- CLIP on the end of the axel shaft that slides into the inside of the pinion gear (use a extending magnet) keeps gear oil on your hands and from dropping it into the pumpkin housing. then all you have to do is slide the axel shaft out. then replace the seal .

Jul 01, 2008 | 1990 Jeep Wrangler

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...