Question about 1999 Volkswagen Golf

1 Answer

My indicators do not work even though my hazard lights work fine and also the lamps flash when I open my car

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 204 Answers

Your car has 2 Flashers in the fuse box one runs your normal turn signals and the other one runs your emergency flashers if you only see one of the flashers in the fuse box check on the back side for the other flasher. this should fix the problem for you the flashers are only about 5 usd apiece
please leave me a rating
thank you

Posted on Apr 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

2 Answers

Left turn signal lights are not working


In my case the left front turn indicator lamp worked, but not the left rear indicator, although all the lamps would turn on with running lights activated, as well as the backup light and 'night-light' mode. The left rear turn indicator would not work with the hazard lights activated. I tested the combination switch (this is the left/right turn indicator switch you use when driving to indicate which direction you are going and is mounted/located on the steering column) and it tested O.K.. I had good continuity from the combination switch black wire, and resistance on the blue-white wire from there to the left rear turn indicator lamp, as well as good continuity on all wires going out from the left parking light fuse. Since the Haynes manual indicated that the flasher module was probably good if it made the tell-tale clicking sound, I was feeling perplexed. So I took it into a local shop that specialized in auto electrics and it turned out to be the flasher module. I was under the impression that it operated in a straight-forward left-right manner, but apparently it has a different circuit for each turn indicator lamp. So even if it is making the appropriate clicking sound when the combo switch is flipped, it could still be the flasher module. Obviously the manual leaves a bit to be desired in the troubleshooting of malfunctioning turn indicators.

Sep 07, 2012 | 1998 Dodge Caravan

1 Answer

1999 oldsmobile aurora side marker light flash on and off when the car is turned off


Power is appliedat all times through the 20A HZRD/ STOP LPS fuse in the right rear junction block. The ORG wire connects to the hazard flasher and the BRN output wire connects to the A5 terminal of the TURN/HAZARD switch assembly. When the HAZARD switch is engaged, power is applied to the front and rear turn signals and the left and right turn indicators in the instrument cluster, causing them to flash. Obviously an open fuse, a defective flasher, a defective HAZARD switch, or a defective TURN/HAZARD switch assembly will prevent the lamps from flashing. If the turn signals operate normally, they are not the problem.

Sep 05, 2012 | 1999 Oldsmobile Aurora

1 Answer

Turn signal not working


Press the Hazard switch on and check the turn indicator lamps. Replace the faulty lamps.
If the hazard lights do not work then the trafficator flash can is faulty provided the trafficator fuse is OK.
Check the fuse for the turn indicators, if it is blown the replace the fuse.

Dec 11, 2011 | 2002 Kia Rio

1 Answer

I have a 99 Pontiac Sunfire, 2.2L and my turn signals quit working. I replaced the combination switch and the flasher/hazard relay, and still no joy. The problem was intermittent, and now it's just dead....


It will turn on when I hit the button and the turn signals do work. All of this has led to my ABS lights to come on as well. ??????????? Your best bet , take it to a qualified repair shop or learn to do better explanation's ! Or lean to do automotive electrical testing .
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts
Electric Testing Techniques You Need to Know

How to Use Multimeter to Troubleshoot Common Problems

Do you know what a wiring diagram is ? How to use a DVOM - digital volt ohm meter ? Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. year make ,model and engine size. Under system click on lighting ,then under subsystem click on turn signals . Click the search button then the blue links .Check power an ground circuits ! This is how we diagnose electrical faults , not just replacing parts .

Turn Lamps
Voltage is applied through the TURN fuse and the turn/hazard flasher when the ignition switch is in the following positions:
• RUN
• BULB TEST
• START
The voltage travels to the contact in the hazard switch. The hazard switch is located in the turn/hazard-headlamp switch assembly. This contact is normally closed.
When the left turn signal is turned on, voltage is applied to the following components.
• The left turn indicator
• The left front park/turn lamp circuit 14
• The left rear turn lamp circuit 18
The turn lamps turn on immediately. The current flow heats up the timing element. The timing element is located in the turn/hazard flasher. The timing element repeatedly opens and closes the circuit. This action causes the turn lamps to begin flashing.
The voltage that is applied to the left front park/turn lamp is also applied to the left front marker lamp. If the headlamp switch is in the OFF position, the left front marker lamp will find a path to ground through one of the following lamps. The following lamps provide low resistance paths to ground:
• The right front marker lamp
• The right turn indicator
• The right front park/turn lamps
• The left front park/turn lamps
The left front marker lamp flashes with the turn lamps. The voltage drop across the marker lamp is much higher than the voltage drop across the other lamps. The lamps that are used for the ground path will not flash.
When the headlamp switch is in either the PARK or HEAD positions, voltage is applied through the following components:
• The EXT LP fuse
• The marker lamps
• The park lamps
When the left turn signal is turned on, the left marker lamp will have voltage at both connections. The left marker lamp does not light. When the turn/hazard flasher stops the voltage to the turn lamps, the marker lamp is grounded through the turn lamp. The marker lamp does not go on. The left front marker lamp flashes in the following manner:
• The left front marker lamp flashes on when the turn filament of the left front park/turn lamp goes off.
• The left front marker lamp flashes off when the turn filament of the left front park/turn lamp goes on.
Voltage is applied to the right lamps in the same manner, when the right turn signal is turned on.
Hazard Lamps
Voltage is applied at all times through the following components to the normally open contact of the hazard switch in the turn/hazard-headlamp switch assembly:
• The STOP HAZ fuse
• The turn/hazard flasher
When the hazard switch is turned on, voltage is applied to the following components:
• The front turn lamps
• The rear turn lamps
The following lamps flash on and off:
• All of the turn lamps
• Both of the turn indicators
The front marker lamps flash with the hazard lamps on, just as the front marker lamps flash when the turn lamps are on. If the headlamp switch is in the OFF position, the front marker lamps flash on when the hazard lamps are on. The front marker lights will flash on when the hazard lamps are on if the headlamp switch is in one of the following positions:
• PARK
• HEAD
When the hazard lamps are on, the following conditions apply:
• The turn circuit is always open.
• The turn/hazard flasher controls the lamp.
Park/Marker Lamps
Voltage is applied through the EXT LP fuse, to the headlamp switch at all times. Voltage is applied to the park lamps and the marker lamps when the headlamp switch is in the following positions:
• PARK
• HEAD
The front marker lamps are grounded through the turn filament of the respective front park/turn lamp. The front marker lamps light as a result.
Stop Lamps
Voltage is applied through the STOP HAZ fuse to the brake switch at all times. When the brake pedal is depressed, the brake switch closes. This action applies voltage through the turn/hazard-headlamp switch assembly to the following lamps:
• The high mounted stop lamp assembly
• The left tail/stop-turn lamps
• The right tail/stop-turn lamps


Jun 30, 2017 | 1999 Pontiac Sunfire

1 Answer

My left rear turn signal is out on my 2006 Malibu. The bulb is good, but I replaced it anyway since I had the assembly apart. The left front flasher works fine as well. Before I try and replace any...


Stop lamp an hazard lights work ?
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.

Repair an open, high resistance, or short to ground in the inoperative turn signal supply voltage circuit. Refer to Circuit Testing and Wiring Repairs .
Did you complete the repair?

May 16, 2017 | 2006 Chevrolet Malibu

2 Answers

Electronic/Electrical Problems


sounds like you have a number of problems.
a. hazard lights and no head lamp dimming and no turn indicator, most likely the multi function switch has failed. but check the bulbs first.
b. head lamp bulb is burnt
c.side mirror switch is disconected or has failed

Oct 20, 2009 | 1998 Ford Windstar

1 Answer

My 2000 saturn sl2 turn signals stopped working


HI"
onepx.gif
onepx.gif onepx.gif Vehicles: onepx.gif Make/Models: onepx.gif Model/Build Years: SATURN/LS onepx.gif 2000 onepx.gif onepxblk.gif onepx.gif Defect: onepx.gif VEHICLEDESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES DO NOT COMPLY WITHREQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, ANDASSOCIATED EQUIPMENT." BECAUSE OF A PROBLEM IN THE HAZARD WARNINGSWITCH ASSEMBLY, THE TURN SIGNAL LAMPS MAY NOT WORK OR MAY WORKINTERMITTENTLY WHEN THE DRIVER USES THE TURN SIGNAL LEVER OR HAZARDWARNING SWITCH. IF THE VEHICLE TURN SIGNAL INDICATORS ARE NOT FLASHING,THEN THE TURN SIGNAL LAMPS MAY NOT BE FLASHING. onepx.gif onepxblk.gif onepx.gif Component Affected: onepx.gif EXTERIOR LIGHTING:TURN SIGNAL:SWITCH onepx.gif onepxblk.gif onepx.gif Corrective Action: onepx.gif OTHER DRIVERS MAY NOT BE ALERTED THAT THE VEHICLE IS TURNING AND A CRASH COULD OCCUR. onepx.gif onepxblk.gif onepx.gif Consequence: onepx.gif DEALERS WILL REPLACE THE HAZARD WARNING SWITCH ASSEMBLY. onepx.gif onepxblk.gif onepx.gif Mfr. Campaign #: onepx.gif 99045/00-C-03 onepx.gif onepxblk.gif onepx.gif Mfr. Involved: onepx.gif GENERAL MOTORS CORP. onepx.gif onepxblk.gif onepx.gif # Vehicles Affected: onepx.gif 1395 onepx.gif onepxblk.gif onepx.gif File Date: onepx.gif 07/29/1999 onepx.gif onepx.gif onepx.gif onepx.gif onepx.gif
onepx.gif onepx.gif The vehicle you are working on may or may not be affected by this recall. Contact the vehicle manufacturer for clarification. hope this solves your problem.THANK YOU

Sep 23, 2009 | 2000 Saturn L-Series

1 Answer

Indicator Problem


when you noticed the indicator being on solid, but flashing with the hazards, are you inside your car? I mean have you gotten out of your car to check if the bulbs are working when the indicator thrown and when the hazards are on. A hard on indicator usually means that you have a bulb burnt out. The hazards will still flash as normal when inside the car even if a bulb is burnt out because the hazards do not run via the Electronic Flasher Module. The EFM is what detects a burnt out bulb

Aug 24, 2009 | 2005 Audi A3

2 Answers

Signal lights


its the multifunction switch gone bad

Feb 16, 2009 | Jeep Grand Cherokee Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

302 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77202 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...