Question about Chevrolet Nova

2 Answers

Defrost switch when i slide swith to defrost it wont stay wants to push lever back 66 nova

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Alot of times there is leaves or something in the heater box that stops it from closing all the way.. my 63 chevy II did that..

Posted on Apr 21, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 383 Answers

Len2664: check for a bent control cable or door which is binding due to corrosion. The binding can be taken care of with WD-40.

Posted on Apr 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Heat and air wont blow through vents


The selection door, is operated by 1/4" vacuum hoses. When turning the knob or sliding a lever, to select between floor, vents, or dash deck for windshield defrost, vacuum is created by the valve body and the blower will then blow thru the desired vents. When these hoses/lines are compromised, especially on a vehicle over 15 years old it seems likely, vacuum won't be created, and the last working position, is normally where it stays! Until the lines are replaced.
Good luck.

Mar 24, 2015 | 1998 Buick LeSabre

1 Answer

Why wont my high beams stay on by it self after i let go of the switch. on my 2001 buick regal


High beams are on by pulling the lever toward you temp mode to engage the high beams simply push the lever forward the high beams should engage then.

Sep 23, 2014 | 2001 Buick Regal

1 Answer

1991 JEEPWRANGLER HEAT SWITCH WILL NOT STAY IN PLACE


Slide levers like that usually move a cable. When they will not stay in place it usually means whatever they move is binding up. I suspect your heater valve is binding.

Dec 20, 2013 | Cars & Trucks

1 Answer

Light sheilds wont open and lights wont come on. If i turn on my brights and hold the swith the sheilds open and brights come on but i have to hold the switch on.


This could be a bad switch but im not sure what knd of car this is, there are many cars out that you need to push the lever foward to activate the highbeam lights, pulling back is only to turn on until lever is released, try pushing foward that should turn them on and keep them on until you pull back on the lever, good day.

Oct 20, 2011 | Cars & Trucks

1 Answer

Looking for wiring diagram for 66 chevy11 nova. for the brake switch.


63 to 72 are the same and only have 2 wires since its a pass through switch , they can go on either post

Aug 02, 2010 | Chevrolet Nova Cars & Trucks

2 Answers

66 mustang help


Remove the steering wheel and replace the directional switch

May 31, 2010 | 1966 Ford Mustang

1 Answer

1985 t bird/ignition switch was stuck and had to change the swith on car, and now it wont stay started unlees i hold down the key


it slides up ad down for adjustment. lossen the two bolts ,turn key to acc setting and slide the switch down until the radio works. tighten the bolts and try to to start. this might take several attemps

Nov 21, 2009 | 1985 Ford Thunderbird

2 Answers

Electrical problems/ no dash lights - no brake lights clicking sounds from twlight sentenail


I just fixed this problem with my 99 Aurora. There is light control module located under IP on left side. It has P/N 25640703...19PPL. I pulled it out (if slides out easily) and one of the pin in 6 pin connector was loose and corrorded. I soldered that. The board on the module could be pushed out by opening the back cover of the box. Good luck!

Nov 07, 2009 | 1999 Oldsmobile Aurora

1 Answer

My headlights turn off when the brights are on


Hello, I beleive that you are going to find that the multifunction switch(turn signal swith) is at fault. here's what to do. Take the lever and rapidly pull back and push foward with a little extra not much but a little you don't want to break the lever, just dislodge the contacts.The internal contacts are self cleaning but they don't always work that way.Just give it a try and you will see it may take a few minutes to dislodge but it is a whole lot cheap than just replacing the switch.Please rate this answer, Thank you.

Mar 01, 2009 | 1995 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...