Question about 2008 Nissan Versa

2 Answers

Brake light replace

How do i get to thebrake light bulb to replace

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Two 10 mm nuts are easily visible. Where are the others and how do you access them?

Posted on Jun 08, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

From inside the hatch back/trunk. Open access door and remove the 3 or 4 nuts that hold the light in place. Have a 8mm or 10mm socket on a nut driver.

Posted on May 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I take off thebrakes pressuer switch


Hi Tom:
If you open the hood (bonnet) and look at the brake master cylinder there should be an electrical connection. The thing on the cylinder that the wires connect to will be the switch.
I'd try unpluging it and then use a continuity meter to try to check the switch function.
DEFINITELY replace the switch if it is not functioning correctly.
It would be DANGEROUS to simply dis-connect it and then drive without brake lights.

Aug 06, 2016 | 1993 Toyota Corolla

Tip

Brake Lights Dull or Flickering - All Cars



Dull or Dim Brake Light Repair: If your car has a dull or dim brake light it is dangerous to you and other drivers. A dim brake light is a mystery to most people because the bulb is working, just not correctly. First confirm a new and correct brake light bulb has been installed. Next, turn the ignition key to the "on" position and have a helper depress the brake pedal. With the bulb installed touch a grounded test light to the outer bulb holder ring. If the bulb brightness changes the bulb socket ground has high resistance and needs to be repaired or replaced.

Flickering Brake Light Bulb Repair: A flickering brake light bulb can be very distracting and annoying. A brake light flickers because the power or ground is being obstructed momentarily. The most common cause for this condition is a loose fitting bulb socket. To check for this condition remove the brake light bulb in question, while a helper hold their foot on the brake pedal move the bulb around slightly in the socket. If the bulb flickers replace or repair the bulb socket as needed to regain proper brake light bulb operation. If the brake light bulb socket tests ok wiggle the brake light fuse and wiring at the brake light bulb socket, brake light switch and turn signal switch (American cars). If the brake light bulb flickers repair the component or wiring as needed.
Preferred Procedure: Always replace brake light bulbs with manufacturers recommend replacement bulbs. If you cannot find the correct replacement bulb part number consult an auto parts store for additional manufacturer information.
Common Problems
When brake light bulbs are replaced with the incorrect bulb causing no or dim brake light operation
If the brake lights stay on continuously it could mean the brake light switch has failed or an adjustment is needed.

on Dec 18, 2009 | Honda Civic Cars & Trucks

1 Answer

1985. Where's the brake switch?


Brake Light Switch Replacement - YouTube

? 7:47
https://www.youtube.com/watch?v=CU2Q9gO3UfE
Sep 25, 2011 - Uploaded by Clyde Lettsome
Replacing a malfunctioning brake light switch in a automatic 1994 ... a problem where my brake lights don't turn on when I press thebrake, But ...

Nov 26, 2015 | Toyota Camry Cars & Trucks

1 Answer

After i change thebrake switch will my fan blower for my heater and ac start working agian


No it won't.The brake switch is for brake light,interlock shift solenoids,transmission TCC controls,and stoping the vehicle, You fan blower has a completely different power supply that is independant from the brake electrical system, For you fan blower to operate its either the fan resistor blower or the fans control switch to the fuse

Mar 19, 2012 | Cars & Trucks

1 Answer

1997 GMC Safari van brakes would not operate when the brake pedal was pressed, infact they would not push down at all, until thebrake pedal was push numerous times. The anti-lock brake light was on prior...


The ABS light is usually a speed sensor problem and is a GM nuisance . it should not affect normal braking. It might be a booster for power assist problem, which will affect normal braking (expensive). Get rid of that old GMC.

May 23, 2017 | 1997 GMC Safari

1 Answer

Why does the brake light keep coming on when hit a bump


your brake light is probably coming on because the fluid is to low in the resevoir. ther is a sensor in the brake fluid resevoir that is on a float. if the fluid gets to low the sensor tells thebrake light to come on . so if the fluid is just high enough to keep the light off, everytime you hit a bump the fluid sloshes around causing the float to drop and the sensor to turn the brake light on. also when your brake fluid level is low it tells you that you will either need new brakes soon or you might have a leak.

Dec 08, 2010 | 2000 Chevrolet Malibu

1 Answer

Thebrake lights on my '98 ford won't shut off even after i disconnect wiring connector from brake pedal unit.


The wiring connector is shorting causing the power to flow through.Hope this helps.

Aug 12, 2010 | Ford E-150 Cars & Trucks

1 Answer

My back Two break lights are not working i have replaced the socket and the light bulb its self when i turn the flashers on they are blinking the but the brake its self doesnt work what do you think the...


Have you checked on the ground to the buld assembly. Ifnot check using a voltmeter/multimeter for voltage on the brake lamp if not check from the brake lamp to the lamp assmebly. Also check th fuses if the voltage is absent on the rear lamp. You can also use a 12 volt lamp to test with one side connected to ground and checking for the lamp to light when thebrakes are kicked. I am sure it will be easierr to trace this way and find the solution. Good day

Aug 10, 2010 | 2002 Dodge Durango

1 Answer

I cannot get the car out of park


see if thebrake lights work, the park is locked if the brake pedal is not pushed, so a defective brake light switch will cause your problem, let me know what you have.

Sep 18, 2009 | 1997 Dodge Neon

2 Answers

84 Eldorado squeaks when driving and stops when i press thebrakes


shot in the dark but you may want to check your shocks

Apr 16, 2009 | 1984 Cadillac Eldorado

Not finding what you are looking for?
Cars & Trucks Logo

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...