Question about 1996 Jeep Grand Cherokee

1 Answer

1996 jeep cherokee intermittin stalling

Have changed all sensors, plugs, wires, distributor .......

Posted by on

  • karo715 Apr 23, 2009

    We have checked everything with the fuel and have ruled that out.

    We are thinking it is electrical poss. the pcm,

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

U have to check you injectors, if this is not the problem check your fuel filter it not getting gas and then check your gas lines, Get a compressor and blow the lines out, Look for rust and dirt.

If this don't work try checking you injectors again then check to see if your getting enough gas? Pump the gas peddle then go to the hood and see if you smell gas? if not? it your fuel pump orFuel Filter, and or lines clogged up. If your getting gas up to the front of the motor then it in your injectors? it one or all.

Posted on Apr 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 jeep grand Cherokee Larado stalling for no reason. we have looked or changed coil, fuel pump, relays, cam sensor inside distributor, this thing still stalls out, but starts right back up.


Crank sensor. Its on the passenger side on the top of tranny. Will have either 1 or 2 10mm bolts holding it on. And a plug. My 94 had the same problem. It would run fine then you shut it off and all it woild do is crank. Wait like an hour and it will start back up. New crank sensor and it was fine

Sep 13, 2015 | 1993 Jeep Grand Cherokee

2 Answers

1996 jeep cherokee stalls, I've replaced the throttle position sensor, MAP sensor, and carbeurotor. What else could it be?


You replace sparkplugs,plug wire,tps,map,cap and rotor.Thats good,If the vehicle runs and you come to a stop and it stalls,That is the IAC (Idle air control) you say it ran fine for a week now its acting up, Service the IAC or get it replaced.

Mar 21, 2012 | 1996 Jeep Grand Cherokee

1 Answer

Runs fine then starts missing real bad then runs fine again. changed fuel pump and filter, plugs, plug wires, and distributor and still no luck


check the ignition coil, crank position sensor, and any wiring. that check engine light should be glowing though when it misses...

Feb 27, 2011 | 1996 Jeep Cherokee Country

1 Answer

Stalls and backfires 1997 jeep grand cherokee limited replaced the map sensor, coil rotor. distributer, spark plugs, spark plugs wires. throttle body pressure sensor ,ingnition coil IAT sensor. amd still...


you need to check the fuel pressure,and did you mean you replaced the distributor or just the rotor because inside the distributor is a pickup plate that some times causes this also 02 sensor can cause this.is your check engine light on if so go to chain auto parts store they usually read your codes for free.

Nov 26, 2010 | 1997 Jeep Grand Cherokee

2 Answers

My 1996 grang cherokee jeep 4.0L keeps skipping after changed plugs, wires, and distributor cap. Will i need a new ignition coil?


how about a bad injector. unplug one at a time to see which one is not spraying. otherwise do a compession test on each cylinder.

Mar 27, 2010 | 1995 Jeep Grand Cherokee

2 Answers

1996 jeep cherokee not getting fire out of the coil wire. changed the coil and the crankshaft sensor, still not getting fire what else should be checked?


i believe the camshaft sensor is internal in the distributor on this model and must be replaced as a complete distributor.also be sure to wiggle the connector at the throttle position sensor to make sure a bad wire is not taking down the entire 5 volt referrence circuit.

Dec 04, 2009 | 1996 Jeep Cherokee

2 Answers

Hesitation when driving 1996 jeep grand cherokee


Try changing your spark plugs and plug wires.

May 02, 2009 | 2002 Jeep Grand Cherokee

1 Answer

1996 Jeep Gand Cherokee won't start in the rain Thinking distributor and wires. Is the distributor hard to change out?


Don't change the entire distributor, just cap, rotor and wires. Make sure you know where each wire goes. (best to replace them one by one) Use high quality parts and they will give you better service.

Apr 21, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...