Question about 2000 Daewoo Lanos

1 Answer

I changed the master and slave cylinder on my 2000 daewoo lanos and u can feel it almost release than nothing. any suggestions

Posted by on

  • horlecs Apr 30, 2009

    i bled the line was it just not enough

  • horlecs May 01, 2009

    yes i did but pedal not totally stiff should i keep bleeding

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 48 Answers

You need to bleed the system.

Posted on Apr 30, 2009

  • scott_77
    scott_77 Apr 30, 2009

    Did you bleed it until fluid squirted out the bleed screw, and you got a solid pedal? Also did you make sure there is enough fluid in the reservoir?

  • scott_77
    scott_77 May 02, 2009

    There could be air in the master cylinder.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Daewoo lanos clutch is soft but the reservoir is still full and i see no leaks what could be the problem. the car's engine has been recently fix after a year of not driving it.


the clutch is relatively easy to operate so what dp you mean by soft
right to the floor with no clutch action' --replace the clutch slave cylinder and clutch master cylinder and bleed the system

Jun 30, 2017 | Daewoo Cars & Trucks

1 Answer

I am about to replace the clutch slave cylinder with anew one please provide the procedure and include the hydraulic bleeding procedure


use a bar to hold slave cylinder arm in towards the slave ,then open bleed and assistant pushes down ,then colse nipple and repeat till teh bar is being pushed against your pressure ,that should do it then leave a brick on the master pedal overnight so any air thats left will rise to the and through the master ,it will be perfect then

Dec 23, 2010 | 1999 Daewoo Lanos

1 Answer

Clutch cylinder


no at the end of clutch pedal

Jul 18, 2009 | 2000 Daewoo Lanos

2 Answers

Daewoo lanos 2000 car is misfiring and wont run properly firing on cylinders 1 and 4 misfiring


have you changed the ignition wires? perhaps firing order crossed? if not coil pack or ignition wires faulty how do you know it is not "FIREING" on 1 & 4 have you tested it with a spark tester tool???

Dec 23, 2008 | 2000 Daewoo Lanos

1 Answer

2000 daewoo lanos


Then this is an air issue, you may need to have it pressure bleed.

Nov 23, 2008 | 2000 Daewoo Lanos

1 Answer

Front brakes stick on


either your calipers are sticking and need replacing. OR the hoses have failed internally. and need replacing.. very rare but possible the master cylinder is not allowing the fluid to return usually caused bu a booster failing and causing some down travel in the master cylinder. I'd start by raising the front end up. appling hard brake pressure. turn the tire.. then loosen the brake bleeder to check for pressure. if the bleeder sprays fluid and the brakes release forget the calipers. if they are still tight then replace the calipers. pump them up again if they released.. and break the line free at the master cylinder. if they don't release then replace the hoses..

Nov 16, 2008 | 1999 Daewoo Lanos

4 Answers

Car will not drive, is it clutch or cabel


my daewoo lanos wont shift into gear/s while running even when clutch is depressed all the way

Nov 12, 2008 | 2001 Daewoo Lanos

2 Answers

Hydraulic clutch for jeep wrangler 2000


hello usaully it is on the slave if not try to hold the clutch pedal in overnight with a stick or something take the cover off the master for the slave so air can escape thru the top goodluck

Sep 18, 2008 | 2000 Jeep Wrangler

4 Answers

Diagnostic codes for 200 Daewoo Lanos..........


Do you feel a misfire?? Random misfires are usually caused by a lean fuel mixture, the reasons that cause this a to many to list here.

Jul 23, 2008 | 2002 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...