Question about 1998 Nissan Maxima

2 Answers

Engine misses when accelerating DOWN THE RD

ENGINE STARTS FINE IDLE OK BUT WHEN MOVING OFF AND DEPRESSING ACCELERATOR ENGINE FEELS LIKE ITS ABOUT TO STALL AND CUT OFF

Posted by on

  • yadayada
    yadayada May 11, 2010

    is this a miss or just a loss of power? if it is a miss the check engine light would be on, please explain.

  • Anonymous Mar 29, 2014

    Engine stalls when using brake,headlamp,heater ECT. Any power drain makes it stall. Engine will only restart by cutting power drain.

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

Could be your (air flow meter,,)they give alot of trouble on nissans...unplug it and if it runs a bit better then thats it,,,

Posted on Apr 20, 2009

  • Samuel paraide Jun 19, 2016

    What I did was,I change a airflow meter, the old one was faulty, new air filter changed.new sparkugs changed

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have the same problem. Could be the fuel pump, fuel filter, fuel injectors or the fuel generator. Its a fuel problem, Im 95% sure of that.

Posted on Jul 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine cut out


Sounds like you may have fuel filter problem. you may want to check the pump and filters located in or near the fuel tank.
Go directly to the source ( Fuel Tank, Pump, Filters, Fuel Pressure Regulator and Injectors )
You may have water or grit in the fuel
Hope this helps

Mar 22, 2014 | GMC Sonoma Cars & Trucks

Tip

How to reset ECU,Throttle and Accelerator Position Learning


Hi.

Below the procedure to reset ECU,Throttle and to perform Accelerator Position Learning on Nissan. It works on Titan, Altima, Infinity, pathfinder and other models.

ECU Resetting


While performing the procedures below, ensue that you are respecting the times stated. If the steps are not done within the specified times, the module will not reset. You will need to use a watch or a chronograph while performing the procedures.

Procedure:

1. Ensure that the accelerator pedal is fully released, set ignition switch to the “ON” position, then wait 3 seconds.
2. Follow the steps a and b below, repeat the two steps in sequence quickly for five times within 5 seconds.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal in full.
3. Wait 7 seconds, then depress the accelerator pedal completely, and hold it for about 10 seconds until the CEL (check engine light) starts blinking.
4. Release the accelerator pedal while the CEL is still blinking.
5. Wait 10 second.
6. Depressthe accelerator pedal in full and hold it for 10 seconds or more.
7. Fully release the accelerator pedal while the CEL light keeps flashing.
8. Turn the ignition switch to “OFF” position and start the vehicle. If procedure has been done correctly, then the light light will turn off.
If the light continues to stay on, repeat the procedure.

Accelerator Pedal Release Position Learning

Procedure

1. Ensure that the accelerator pedal is completely released before starting the procedure.
2. Turn the ignition switch “ON” and wait at least 2 seconds.
3. Turn the ignition switch “OFF”, and wait at least 10 seconds.
4. Turn the ignition switch “ON” and wait 2 seconds.
5. Turn the ignition switch “OFF” and wait 10 seconds.

Throttle Valve Closed Position Learning

Procedure

1. Ensure that accelerator pedal is completely released.
2. Turn ignition switch to the “ON” position.
3. Turn ignition switch to the “OFF” position and wait at least 10 seconds.
Ensure that the throttle valve moves after turning the switch off.

Idle Air Volume Learning (Throttle Position Learning)

Procedure

1. Follow the Accelerator Pedal Released Position Learning described above.
2. Do the Throttle Valve Closed Position Learning also described above.
3. Start the engine, and allow warming up.
4. Turn the ignition on “OFF” positionand wait 10 seconds.
5. Ensure that accelerator pedal is fully released, then turn the ignition switch to “ON” position, and wait 3 seconds.
6. Repeat the steps a and b below five times within 5 seconds in sequence.
a. Push hard the accelerator pedal untill fully depressed.
b. Release the accelerator pedal until reaching full extension.
8. Wait 7 seconds or more, depress the accelerator pedal completely and hold the pedal down for about 20 seconds until you see that the Check Engine Light stops blinking and starts getting steady..
9. Rrelease completely the accelerator pedal within 3 seconds after the light coming ON.
10. Start engine and let it run at idle for about 20 seconds.
12. Test the engine to ensure the idle speed and ignition timing are set correctly.

Regards.

on Mar 25, 2010 | Nissan Titan Cars & Trucks

1 Answer

Engine revs but no acceleration


Clutch plate and pressure plate seem to be too weak to pull the car. Or one of the CV joints is detached from the gear box. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

1 Answer

2005 Mazda 6 4cyl AT Idles high after driving a while.


I would check the pedal position sensor. Do it when it's hot.
Mazda Car 2005-06
  • Accelerator Pedal Position Sensor

    Description & Operation

    A power supply is applied on the Accelerator Pedal Position (APP) Sensor (main) power terminal from the PCM. The ground terminal is grounded with PCM. When the accelerator pedal is moved from the idle position to the fully opened position, the resistance between the accelerator pedal position sensor (main) output terminal and ground terminal will increase according to the depression.
    A power supply is applied on the Accelerator Pedal Position (APP) Sensor (main) power terminal from the PCM. The ground terminal is grounded with PCM. When the accelerator pedal is moved from the idle position to the fully opened position, the resistance between the accelerator pedal position sensor (main) output terminal and ground terminal will increase according to the depression.

Testing

  1. Connect a suitable scan tool to the diagnostic connector. Select APP1 or APP2 percentage.
  2. Turn the ignition switch to the ON position.
  3. Measure the voltage at the PCM terminal and ground with connectors connected:

    APP1-8% load or 0.4 volts with the accelerator pedal releasedAPP1-60% load or 3.0 volts with the accelerator pedal depressedAPP2 -8% load or 0.4 volts with the accelerator pedal releasedAPP2 -60% load or 3.0 volts with the accelerator pedal depressed
  4. If any check above does not meet the specifications, check connectors and wiring between the sensor and PCM. If ok, replace PCM.
  5. If the measured values are outside the standard value range, or if the load % and/or voltage does not change smoothly, replace the sensor.
  1. Connect a suitable scan tool to the diagnostic connector. Select APP1 or APP2 percentage.
  2. Turn the ignition switch to the ON position.
  3. Measure the voltage at the PCM terminal and ground with connectors connected:

    APP1 %-31.0-32.4% with the accelerator pedal releasedAPP1 %-69.8-81.8% with the accelerator pedal depressedAPP2 %-20.2-21.4% with the accelerator pedal releasedAPP2 %-58.8-70.8% with the accelerator pedal depressed
  4. If any check above does not meet the specifications, check connectors and wiring between the sensor and PCM. If ok, replace PCM.
  5. If the measured values are outside the standard value range, or if the load % does not change smoothly, replace the senso

0996b43f80203317-l15fcbeisfileg1jtnhunp3x-3-0.gif

Jul 23, 2017 | 2005 Mazda 6

1 Answer

Engine idles but does not accelerate when pressing on the gas pedal?


what car is it? your car using carb or fuel injection

Jul 27, 2012 | 1995 Nissan Altima

1 Answer

98 626 2.0 run idles but lungges and won't excelerate will idle. changed ecu not that


Check the air intake boot between the air cleaner and engine. It is a black rubber, accordian looking tube. Check the accordion tube area and down in the grooves for any tears that would allow unfiltered and unmetered air into the engine. Tube can look fine just sitting there but when trying to accelerate the engine torque will allow engine to move and open up the tear causing a lunging or surging feel on acceleration but not at idle.

May 25, 2011 | 1998 Mazda 626

1 Answer

Idle ok,slow acceleration fine,accelerating quickly miss-fires


Sounds like you have a leaking cylinder head gasket

Jul 18, 2017 | 1992 Ford Escort 4 Door

2 Answers

Engine misses when accelerating DOWN THE RD


the idle controls could be the problem

May 02, 2009 | 2001 Ford Expedition

2 Answers

Hesitation , skipping,engine cuts out when accelerating


Im having the same issue I believe. I have a 94\' Chevy 1500 and when i accelerate it will jerk like the gas has cut out but it wont stall. It just jerks and slows me down. It only seems to do it when going up a hill. I feel like it could be the fuel pump or possibly some intake gaskets?

Feb 28, 2009 | 1993 Chevrolet Lumina

Not finding what you are looking for?
1998 Nissan Maxima Logo

Related Topics:

471 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...