Question about 1996 Ford Mustang

1 Answer

How to fix a leak around the block of a 1996 Ford Mustang...it is my sisters car and my mom just replaced the entire motor...there is a leak around the block and she tried to seal it but was running back and forth between the mustang and a Ford Bronco and we think the sealant just dried to fast. Any suggetions?

Posted by on

  • 1 more comment 
  • dirtyhillbil May 11, 2010

    What is leaking: oil, antifreeze, fuel? Is the engine block cracked? Where specifically is it leaking from and how severe?

  • medley_r May 11, 2010

    what is leaking

  • yadayada
    yadayada May 11, 2010

    around the block?? could u please give more info on this.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Replace the gasket. where is it exactly? did a shop replace the motor? If so bring it back

Posted on Aug 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont my mustang take the 110 amp alternator??


what year mustang my mom has a 1996 gt convertible with a rare cobra engine in it from factory and she was having the same problem had it in to dealer 20 times and they couldn't fig it out one day i was under it looking around and found a wire shorted on drivers side stuck under the motor mount had to undo mount and lift motor and got it out and taped it up been fine ever since

Mar 04, 2015 | Cars & Trucks

1 Answer

Just looking for a diagram of the 1996 ford mustangs fuse panal


Go to this FREE Ford website to download the owners manual for your Mustang.
The fuse block diagram and location infomations starts on page 280.
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

Apr 02, 2011 | 1996 Ford Mustang

1 Answer

The top won't go down on my 1996 Mustang convertible. What should I check on?


If motor does not run when the switch is pressed then check your fuses, the switch and the connector at the top motor to see if it is getting power. Remember the car should be in park with the emergency brake on. The key switch has to be in the run position. If you can hear the motor running check for the smell of hydraulic fluid. It could leaking from the cylinders that pull the top down and push it up. If one or both will not hold pressure. Replace cylinders if bad.

Jul 08, 2010 | 1996 Ford Mustang

1 Answer

1996 mustang v6 3.8 reverse works fine, but no forward gears. had to add 3 quarts trans fluid. don't see any leaks.


its impossible to lose that much fluid with out a leak. the was so low that it has burned your clutches out. would have to rebuild or replace entire transmission

Apr 05, 2010 | 1999 Ford Mustang Cobra

1 Answer

I have a 1996 mustang 4.6. when i start my car it runs at 2000rpm.will finally sttle at 1000rpms after few min. the rpms will not drop when you push in the clutch. just put a new idle air control valve on...


perhaps there is a air leak at the mating surface. if you have a bottle of propane, use it to ckeck for leaks around the gasket/mating surface. start the engine. open the valve on the bottle DO NT LIGHT direct the gas around the mating surface. if the r's go up you have a leak. it is possible that since this is new, the computer was used to the old one and needs time to adjust

Feb 24, 2010 | 1996 Ford Mustang

1 Answer

Mustang convertible plastic window help


unless the window is the type that zips out you will probably have to replace the entire top. It may be possible to sew a new window in. Check with a shop that specializes in upholstery

Feb 15, 2010 | 1996 Ford Mustang

1 Answer

Mustang gas tank removal


yes to do it the right way you should take the tank out of the car empty and rinse out then replace when completly dry

Jun 24, 2009 | 1996 Ford Mustang

2 Answers

1996 ford mustang convertible ac blows cold only from defroster


Check the vaccum line at the vacuum distribution block (to the right of the brake master cylinder). It's the smallest vacuum hose.

Jun 11, 2009 | 1996 Ford Mustang

1 Answer

Convertible rear window leaks water


Purchase some Permatex clear RTV silicone adhesive sealant from an autoparts store run a bead around the window where you have a leak; smooth the sealant like you would caulk wait 24 hours before use

Jun 03, 2009 | 1996 Ford Mustang

Not finding what you are looking for?
1996 Ford Mustang Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...