Question about Pontiac Grand Prix

Open Question

Tie rods wont come off

We have been trying to get inner tie rod off and the tool wont grab ahold of it auto zone says that the tool that we need but its like its to big to grab it please give us some info on what to do

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 124 Answers

SOURCE: I,ve disconected the tie rod

If it is the inner tie rod you are working on it need to be threaded out on some you can get with a wrench but most you will need an inner tie rod tool. Look at your replacement tie rod you will see the threads and two flat spots that is where the wrench goes. Please rate.

Posted on Dec 13, 2008

  • 507 Answers

SOURCE: How to replace Inner Tie rod on 1994 Chrysler Town & Country?

222,000 miles? that's a good vechile so far! anyways, do some price checking. new rack and pinions come with the inner tie rods. so if it's like 50 more for the whole assembly, i would but if not, it's up to you. i've changed some rack and pinions on vechiles that were under 150000 due to major leaking. and if you put just new rods in, if it dose start leaking later, you'll get new inner rods again with new system you'll just be paying labor and alingment charges again. so again, my OPINION is if I'm going to keep it for a while and if it's COST effective, just to do the whole unit.

Posted on Mar 07, 2009

468 Chevelle
  • 81 Answers

SOURCE: How Do I Remove & Replace Worn Inner Tie Rod Ends

Cut band clamp. use tie wrap. Special tool to remove inner tie rod. Autozone or others have them to rent. Must align after replacement

Posted on Mar 27, 2009

  • 4369 Answers

SOURCE: How to change inner tie rod ends?

if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------

  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Posted on Apr 15, 2009

Molson02536
  • 3854 Answers

SOURCE: how difficult to replace inner tie rod end on 06 silverado 2wd?

Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change inner tie rod driver side 1994 accord


You need an inner tie rod tool!!!!!
Run down to auto-zone and rent one. It's like jumbo deep socket.

When you take off the outer tie-rod make sure you count exactly how many revolutions to take it off, then when you put it back juts recount the revolutions and get it exactly the same. You shouldn't need to get another alignment. The tool you can rent at autozone, it's like a long wrench that has just a plain square box at the end you put in this rod thing that the tool comes with and it reaches the inner tie-rod. You will need to take off part number 25's jam nut first as it holds the inner tie-rod against the outer tie-rod. There is a boot that covers up the inner tie-rod end too you will need to grease up that boot really good before putting it back over the inner tie-rod. There is a ring around both ends of the boot, you will need either a ring separator or just pry it off and when putting the boot back just put a zip tie around each end tight, that's what I did cause i didn't have a ring separator. Also, there is a chance if you have an old oem one that the tool can't get to it so you can turn the wheel to move it out so you have more room. Mine was stripped so I had to use some vice grips to get it off. There's also a ring on the inside of the boot at a hose fitting, the other side of the hose goes to the other inner tie-rod on the other side so that when you turn the wheel air moves freely between both tie-rods.

Sep 17, 2011 | 1994 Honda Accord

1 Answer

Remove tie-rod end inner


You'll have to get an inner tie-rod tool. It is a long tube with a crows foot in the end that slips over the hex on the tie rod where it connects the the steering rack. Auto Zone and other part stores will loan you the tool. The tie rod end comes out just like a bolt, turn it counter clockwise to remove it.

Feb 13, 2011 | 1994 Eagle Talon

1 Answer

How are the tie rod ends connected to the rack unit at the opposite end of the tie rod from the wheel ? The Tie rod is free to turn. Is this normal ??


The inner tie rod is threaded onto the rack. There is a tool called an inner tie rod end tool, than will help make it a lot easier to remove. The tool can be found at any good parts store or tool store. The shaft of the inner tie rod will spin. It has a ball that is pressed into a socket. The socket is the part that has the threads onto the rack.

The way you tell if they are back is by grabbing the tire at the 3 and 6 position and pushing/pulling. If you feel any movement than look carefully at the inner tie rod and the outer tie rod to see which one is letting the wheel move.

Sep 27, 2010 | Oldsmobile Silhouette Cars & Trucks

1 Answer

Replace inner tie rod ends on 2005 gmc 1500 . have ev370 moog parts is there a special tool 2 remove the inner rod ends from rack &pinnion. Ihave the tools 4 the outer but the inner looks like a big...


Yes, there is an inner tie rod end wrench, there are a few different types of wrenches available. You should be able to borrow one from one of your local parts stores. (Oreillys, Auto Zone, Napa, etc..)

May 31, 2010 | 2005 GMC Sierra

2 Answers

Tie rod broke and I am trying to remove the old one but can't figure it out. I have removed the nut from the outer tie rod but it still does not come off the tire. The inner tie rod I have no idea how to...


The tie rod close to the tire. Your have to get a pitch fork and a hammer.
If you don't have a pitch fork,
Then hit the spindle to make that outter tie rod end drop down.
make sure the bolt is remove.
Little hammer is not going to work you will need like a 32oz .
Once you have it loosing you will have to go counter-clock wise turn to remove the outer tie rod end from the inner tie rod, Remember count the turn very important to install it back. for you Toe Alignment.


The inner tie rod end will you will need a tool call tie rod end removal & install. It's a long tube with specail clip to removal & install.
Maybe you can rent it. Or buy it habor freight tools or something.

Let me know

Sep 20, 2009 | 1990 Nissan 240SX

1 Answer

99 Park Avenue Inner Tie Rod removal


best thing i can tell you is to purchase a haynes auto repair manual at any auto parts store. 17$ it'll tell you step by step instructions.

Jul 01, 2009 | 1999 Buick Park Avenue

2 Answers

Replacing tie rods


Maybe just a tie rod fork ...you can probably get a loaner free of charge (just requires a deposit) from Auto Zone or one of the chain parts stores.

Apr 01, 2009 | 1991 Mercury Sable

1 Answer

1996 chrysler concorde, how to take off the inner tie rod?


I used this website: http://www.allpar.com/fix/intrepid-steering.html It worked perfectly. To add to it, I used a tie rod puller tool rented from Oreilly Auto Parts for only a few bucks, to press the old bushing out of the inner-tie-rod end. Worked very well. Easier than removing the entire tie rod, and hammering it out. However, removing the entire tie rod would make re-assembly easier. If I did it again, I would strongly consider removing the driver side tie rod from the car, then attaching the inner tie rod end 1st. Meaning, attach the passenger side inner tie rod 1st, then the driver side inner tie rod with new bushing, then re-attach the drivers side outer tie rod. That would probably be the easiest way on this 1996 dodge concorde, due to the fuel line that's in the way....

Mar 17, 2009 | 1996 Chrysler Concorde

1 Answer

I need to know how to get the inner tie rod off my van.


if you buy the tie rod from auto zone they will also print you out a diagram of how to remove and install and what tools are needed to do the job and if you need too you can also rent the tools from them

Jan 11, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...