Question about 1996 Jeep Cherokee

1 Answer

Cylinder misfiring replaced plugs, wires, cap, rotor. It still feels like a cylinder is misfiring, and there is a slight knocking. It's going through a quart of oil a week.

Posted by on

  • Richard Scordino May 11, 2010

    Were any of the plugs you removed fouled?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 74 Answers

Hello and welcome to FixYa. check you engine for any noticeable signs of oil excessive in 1 particular area if you don't see any excessive oil stain. Try doing a valve job inspect lifters and push rods make sure they are not warped or clogged replace valve cover gaskets that should take care of most of your issues I would also have timing checked. If knocking continues. replace Rings and check for damaged main rods on the crank shaft in the bottom of the engine which could be knocking around in the oil pan Loosing Oil thru a bad gasket no worries easy fix but burning that much oil is definately a sign of time for engine overhaul or replacement motor. I hope this will help get you going. Please Rate Me. And you can always Ask Me. cylinder misfiring - aymloekh0fg4hpz2e87n86udvs4fowqwshuaaaaasuvork5cyii=

Posted on Apr 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have s 1997 Honda accord that has the check engine light on. Had the codes read and it says there is a misfire in two of the cylinders. I replace plugs, wires, cap, and rotor. Stills has the problem. Not...


did you have the cods cleared ever ? or is it a misfire you can feel when the motor is on, if this is the case check the fuel injectors in those cylinders, this will toss a misfire code also

Jul 22, 2011 | 1997 Honda Accord

1 Answer

I have a 1998 dodge caravan. it keeps giving me a P0300 and P0305 code. I replaced the cap,rotor, plugs and wires in june 2010. Once again I just replaced the cap and silicone sprayed it. however it's...


Good Evening, I am sure you know the 0300 is a random cylinder misfire and the 0305 is a cylinder 5 misfire. One would not think that you should have to do another tuneup since you did one in june. I would say the parts are under warranty and if you feel that is what is wrong you should be able to replace them. However you could have a vacuum leak, or injector going bad. First I would pull that plug and check compression on that cylinder to start with. Also check out the plug while it is out. And go from there. Cheapest route is of course the re-tune which warrantied parts cost nothing but time. Let me know how it goes.

Nov 02, 2010 | 1998 Dodge Caravan

2 Answers

I have a 1996 crown vic i need to know these touble codes po305 po304


P0304 means that cylinder 4 has a misfire and P0305 is a cylinder 5 misfire. What this means is you may have bad spark plugs, or bad plug wires, or you may need to replace your distributor cap and rotor. I would start with plugs and wires.

Oct 21, 2010 | 1996 Ford Crown Victoria

2 Answers

What do these trouble codes mean po306 cyclinder misfire detected .how do i fix the problem?


it means you have a misfire on the number 6 cylinder

this could be caused by a whole lot of reasons.

start by inspecting for a bad plug wire if it has them

check for fire on the cylinder with a spark test tool from local part store

if it is a coil-on-plug set-up, check the coil for fire

replace coil/plug wire as needed, replace boot on coil if coil needed, replace spark plugs

Oct 11, 2009 | 1998 Chevrolet Blazer

2 Answers

Coil 8 misfire


It if is misfiring on one cylinder. The replace the plug wire first. Make sure plug is good.
If two cylinders are misfiring, then you will want to replace the cap, rotor, or coil pack depending on what you have.

Sep 28, 2009 | 1986 Ford F150 SuperCab

4 Answers

2001 2500hd 6.0l multiple cylinder misfire at higher rpms


If you have someone scan it with a scan tool that gives you data stream they can tell you exactly what cylinder is doing it. You might have a bad coil or wire.

May 16, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Bogging while heavy accelration.


vacuum advance working ? do manuel check with cap and rotor button off and see if it's moving. chris

May 08, 2009 | Mitsubishi Diamante Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...