Question about Ford Mustang

1 Answer

89 4 cyl dont hold water comes out around doughnut gasket and exhust pipe

Dont hold water comes out around doughnut gasket and exhust

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Blown head gasket or cracked head so sorry

Posted on Apr 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the valve cover gasket on a 2002 Saturn L200, 2.2 engine?


Disconnect the camshaft cover grounding strap.Right side of engine.
Remove ignition module, 4 bolts , and disconnect the electrical connection to it. Pull straight up to remove.
Remove 4 spark plugs.
Remove the coolant pipe bracket.
Remove the fuel line bracket.
Remove the 12 bolts holding down the cover, then pry up around the edges GENTLY to remove. You might want to use a rubber mallet at this stage, just don't overdo hitting it, its cast aluminum..
The gasket around the edge and around the spark plug holes don't need sealant, the new design does away with this.
Now would be a good time to check the wear on the Teflon timing chain shield between the camshaft sprockets.
Installation is in reverse order.
Camshaft cover bolts : Tighten to 89 INCH pounds.
Camshaft Ground Strap Bolt : 89 INCH pounds.
Spark Plugs : 15 FOOT pounds.
Ignition coil to camshaft cover bolts : 71 INCH pounds.
Coolant pipe AND Fuel line bracket bolts: 89 INCH pounds.
Good luck.

Feb 21, 2015 | 2002 Saturn L-Series

3 Answers

Smelling hot coolant but not finding visable leak.


Could be burning it through the exhaust,due to a blown gasket ,get someone to rev it up while you stand at the back and check if any water comes out the pipe.

Sep 28, 2014 | 1998 Mercury Grand Marquis

1 Answer

How to put an exhaust donut gasket in


Remove the body harness for the exhaust closet to the dounut. this should give you enoun slack to move the pipe. Assuming your clamp bolts will loosen. Loosen bolts on the doughnuts clamp. remove the clamp. Then pry the tail pipe away from the manifold and remove the old dougnut gasket. Spray it down with WD-40 and wire brush it clean. Insert new dougnut gasket and tighten new clamps down around it.

If the bolts on the clamps are rusted to bladly to loosen then cut off with a reciprcating saw or a hi speed cutting disc. Just becareful not to cut into the exhaust pipe or yourself.

Feb 23, 2011 | 1984 Chevrolet S-10

1 Answer

I have an exhaust leak where the donut gasket is i was wondering if their might be a diagram


What kind of diagram are you wondering about? If you just take off the three nuts that hold the pipe to manifold, you should be able to pull the pipe down enough to get the doughnut gasket out. If not then unfortunatly you will have to remove both sides. Hope this helps you out in your task.

Feb 10, 2011 | 1997 Chevrolet C1500

1 Answer

89 f250 overheated and stalled 3 times. I replaced thermostat and water pump. Looks like water got in my oil as ists foamy and over filled. Truck will turn over and tries to fire but wont start


Sounds like your head gasket has gone bad. you may have noticed white smoke comeing out of the exhust. do not run this engine without changeing the oil or you will destroy the engine, and if the head gasket is leaking it will dump water or antifreeze into the oil again.you can take a compression check on the engine to tell you what head gasket is bad.

Nov 24, 2010 | 1989 Ford F 250

2 Answers

How do i find where an exhust leak is coming


check where the headers come off of the engine exhaust leaks are generally quite loud and you will either be at the headers/exhaust manifold or just as you come off that bend there will be a flange gasket inside the two pipes joining. from the bend to the straight pipe just as it passes the gearbox and starts to straighten out.

Jun 22, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

Bmw 316i automatic 1996. have had head skimmed white smoke coming from exhust the top pipe from raditor is hot but hard the bottom pipe is cold. the oil in head is a caramel cream colour. have put a new...


You have a bad head gasket. You are leaking coolant into the engine block through the cylinders. This is why you have white smoke, and the extra coolant that doesnt get burned off is going into your oil.

Oct 16, 2009 | 1996 BMW 318

1 Answer

Loud exhust


Hi,welcome to fix ya.
usually the ones in the exhaust manifolds where the pipe attaches go bad . there is a metal sleeve that goes inside the donut be sure to use these or the donuts will burn out pretty fast. use a generous amount of penetrating oil on the bolts first they get pretty rusted on these .

Apr 06, 2009 | 1997 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...