Question about 2006 Chevrolet Impala

1 Answer

No a/c 2006 impala

The light goes on on the button for 2 sec then goes out

Posted by on

  • Anonymous May 20, 2009

    outside air reads -40 a/c will not work

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Redirect the ventilation control to the person pictograph, push the interior circulation, and then press the a/c on.

Posted on May 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to unlock 2006 Chevy Impala radio


Procedure:
1. Turn the ignition ON (The radio should display "LOC")
2. Hold down the Radio Presets 2 and 3 buttons for six seconds
3. The radio display changes from LOC to a three-digit number. Write this number down. You now have fifteen seconds to complete the next step.
4. Press the AM/FM button
5. The radio display changes to another three-digit number. Write this number to the right of the first one.
6. You now have a six-digit number, the first three digits are from STEP 03 and the last three digits are form STEP 05
7. Call 1-800-537-5140
8. Press 1 then # (pound). You'll hear "Invalid Code, try again"
9. Press 139010 or 106010 or 206010 or 202107 then # (pound). You will be asked to enter your four or six digit code followed by *
10. Enter the number from STEP 6 then *
11. Listen to the four-digit number and write it down. It will be repeated twice
12. Turn the ignition ON (The radio displays LOC)
13. Use the MN and HR buttons to enter the code from STEP 11
14. Press the AM/FM button. The radio display changes to "SEC". Your radio is now "un-locked" and usable.

Dealership Codes•139010
•106010
•206010
•202107
Troubleshooting
If you fail to enter the correct code eight times, the radio goes into INOP mode. You have to wait an hour with the ignnition on before the radio returns to LOC mode.

http://www.impalaforums.com/chevy-impala-8th-gen-discussion/270328-how-to-reset-gm-theft-lock-radios.html

Jun 05, 2015 | 2006 Chevrolet Impala

1 Answer

I have problem with remote control, my remote control gives me blue light to switch the dashboard on but there is no lights coming on the dashboard. what is the problem


Hi, your remote has probably lost its coding. If you have the owners manual check page 65 learning additional remotes. If not do the following 1. Plug in the 6 pin hopped coded plug to control unit under drivers seat. 2. Press unlock button twice to disarm. 3. Press learn button on hopped coded plug. this erases all pre learnt codes. The led on dash should start blinking once per sec. 4. Press learn button on hopped coded plug again. The led on dash remains on for 4 sec. and then starts blinking faster. Ensure to do step 5 within 25 sec. 5. Press any button thrice on your remote that has a problem. 6. In response led on dash remains on for 4 sec and then blinks once per sec.This indicates that the remote has been learnt. Hope this helps.

Mar 09, 2015 | 2006 Tata Indica LSi

2 Answers

If my 2006 chevy impala ls 3.5 engine has a ABS display light in the dash does that mean I have the feature


It means your anti-lock braking system is not working properly. All Impalas this year come with ABS, the light simply means it is not functioning properly.

Breaks are simple, but as far as the ABS System goes it is something you want to get looked at by a certified mechanic.

Jun 05, 2012 | 2006 Chevrolet Impala

2 Answers

The check engine light (spanner) came on and I saw a message saying that oil life is less that 15%. I quickly went and serviced the car but the spanner sign did no go. Please advise me on what to do.


Place the key into the #2 position (do not start engine). With the oil remaining light showing on the odometer, press and hold reset post for 10 seconds until it starts blinking, then let go. Press it again for 5 seconds and it should reset back to 100%.

Jan 24, 2011 | 2006 Honda Accord

1 Answer

How to manually turn off the check engine light


PULL ECM FUSE FOR FEW SEC. PUT BACK IN OR UNHOOK NEG. CABLE

Dec 05, 2010 | 2006 Chevrolet Impala

1 Answer

Factory remote starter on my 2006 impala LT does not work had it to the dealership a few months ago and the replaced the two key chain remotes, doors will lock and lights will flash when trying but no...


there should be a red reset button under kick panel on driver side press in for 30 sec and release, that should take car of problem , also could be mount on dash on driver

Nov 16, 2010 | 2008 Chevrolet Impala

2 Answers

My service traction control light keeps on going on it then reduces my power engine in my 06 impala


I have a 2006 checy impala and the TCS ( TRACTION CONTROL SERVICE) liught came on..What does this mean?

Feb 25, 2010 | 2006 Chevrolet Impala

2 Answers

How do I get the "change oil" message off my 2008 f 450 superduty?


Message center cluster
#1 press and release setup button until mess. cntr. displays"press reset to begin system check"
#2press and release reset button until cntr. displays"hold reset if new oil"
#3press and hold reset button for 2 sec. and release oil life should read 100%
#4 center displays"setup menu hold reset"

base cluster
#1 press and release trip/reset button until mess. cntr. displays"setup menu hold reset"
#2press and hold trip/reset button 2 sec. until mess cntr. displays"reset for system check"
#3 press and hold trip/reset button 2sec. until mess. cntr. displays"oil life XX% reset if new"
#4 press and release trip/reset button until mess.cntr.displays"hold reset if new oil"
#5 press and hold trip/reset button for 2 sec.and release to reset to 100%
#6 mess. cntr. breifly displays oil change set to 100%.

HOPE THIS HELPS

Feb 10, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

2006 Chevy Impala - Can't Clear Replace Battery in Remote Alarm


There is a fault code present and you will have to take it to a dealership for them to use a Tech II and read the code.

Jun 20, 2009 | 2006 Chevrolet Impala

1 Answer

How do I program my key for my 2006 Chevy Impala?


Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

May 20, 2009 | 2006 Chevrolet Impala

Not finding what you are looking for?
2006 Chevrolet Impala Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...