Question about 2005 Dodge Magnum

Open Question

INSTRUCTIONS TO REPLACE MULTIFUNCTION SWITCH

Turn signals do no cancel, how do i get the multifunction switch out to see if this is my problem

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: turn signal

try a flasher

Posted on Sep 19, 2008

ndguy2481
  • 251 Answers

SOURCE: Replace multifunction switch on Pontiac Gran Prix 2000

no just the top and bottom of the steering wheel cover

Posted on Dec 07, 2008

slfowler29
  • 51 Answers

SOURCE: No high beams, problem is not multifunction switch

Check the headlight switch to make sure that the connections or internal connections aren't corroded. This was a major problem for older fords, so it would be good to check it anyway.

Posted on Mar 26, 2009

  • 58 Answers

SOURCE: 2002 Pontiac Grand Prix GTP / Multi-function Switch

i have the sameproblem. Dealer part was quoted to me at $510.00. All after market parts stores were $350- 450. Try moving the emerg. flasher button while you step on the brakes and someone else watches the lights. I jammed paper beside the button and they work until I can fix it.I had to order the multi-function switch. and you have to pull the air bags to replace it.

Posted on Jul 15, 2009

duane_wong
  • 6826 Answers

SOURCE: Multifunction Switch works intermittantly.

Multifunction Switch -I suspect this switch or the connection at the harness is bad or contaminated. Removal & Installation To Remove:

  1. Disconnect and isolate the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Disconnect wire connector from the back of the multifunction switch.
  4. Remove screws holding multi-function switch to steering column adapter collar.
  5. Remove the multi-function switch.
To Install:
  1. Position the switch on to the steering column and install the mounting screws.
  2. Connect the electrical connectors to the switch.
  3. Install the upper and lower steering column shrouds.
  4. Connect the negative battery cable.
prev.gif next.gif

Posted on Aug 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of signal relay 2002 lincoln ls


That sounds like the multifunction switch is the fault. The flasher on this vehicle is part of the hazzard switch. It recieves power for turn flashing from the turn signal switch. It is very common for the turnsignal (multifunction) switch to become worn and supply partial power to the flasher (hazzard switch) when not on which results in this fast clicking without any lights on. To be certian without taking out any tools whatsoever the next time the clicking happens jiggle the turn signal switch and see if it goes away or changes at all. If it does you need the turn signal switch. I'm going to include replacement instructions for that below because I am confident that is what you will need. Please ask if you have any further questions.



Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
Disconnect the negative battery cable.
Disable the supplemental inflatable restraints (SIR).

zjlimited_707.gif


Remove the tilt lever.
Remove the 3 Torx® head screws from the lower column shroud (3).
Remove the upper column shroud (1) tilting up and unsnapping from the lower column shroud hinges (3).
Remove the lower column shroud (3) from the steering column (2).
Remove the Torx® head screws (1) from the multifunction switch (2).
Object Number: 442014 Size: SH

Disconnect the electrical connectors (3) from the multifunction switch (1).
Remove the multifunction switch (1) from the column (2).
Installation Procedure

zjlimited_708.gif


Position the multifunction switch (1) on the steering column (2).
Connect the electrical connectors to the multifunction switch (1).

zjlimited_710.gif
Install the Torx® head screw (1) to the multifunction switch (2).

Tighten
Tighten the screw to 6 N·m (53 lb in).

zjlimited_711.gif

Install the lower column shrouds (3) to the steering column (2).
Install the upper column shroud (1) to the steering column (2).


Install the Torx® head screws to the lower steering column shroud (3).

Tighten
Tighten the screws to 2 N·m (18 lb in).
Install the tilt lever.
Enable the SIR system.
Connect the negative battery cable.
Ensure that the multifunction switch functions properly.

Mike39819.098075081


Hope helps.

Sep 15, 2011 | Lincoln LS Cars & Trucks

1 Answer

1999 ford f 550 turn signal and hazard lights are not working. fuses are good.


I am not familiar with this vehicle, but I am confortable with wiring diagrams. I pulled the electrical diagram for the model year 1999 HD/350/SUPER DUTY (which would include your F-550). I would suspect the hazard switch in your multifunction switch/arm/wiper lever. It is the only common thing between the 2 systems, and both are wired through 2 different flasher assemblies through 2 separate wires to the multifunction switch/arm. In fact, the hazard lights are a hot battery item and bypass the turn signal switch for the front turn signals as well as the indicators in your dash.

Try to check if your stop lights do come on when you hit the brakes... if they don't, your problem is really with the hazard switch within the multifunction switch/arm.

I do not know if this switch can be replaced separately from the multifunction switch/arm, but from what I found surfing the net, the whole thing (multifunction switch/wiper lever) goes for about 50$. There are some DIY on the internet to replace the assembly, but it would seem it can be a bit tricky to replace for someone not familiar around the steering wheel portion.

Hope this helps.

Sep 14, 2011 | Ford F-450 Cars & Trucks

1 Answer

How to replace the wiper switch in a 2005 chevy trail blazer


YOU HAVE TO REPLACE WHOLE MULTIFUNCTION SWITCH WITH TURN SIGNAL SWITCH, LIGHT SWITCH, WIPER SWITCH HAS TO BE REPLACED.YOU HAVE TO TURN OFF RADIO FIRST THEN REMOVE NEGATIVE BATTERY CABLE.THEN WAIT 20 MINUTES UNTIL AIRBAG IN STEERING WHEEL DISARM.THEN REMOVE THE MULTIFUNCTION SWITCH LOCATED ON THE LEFT SIDE OF THE STEERING COLUMN.YOUR WIPER SWITCH ON THE MULTIFUNCTION SWITCH.

Aug 16, 2011 | 2005 Chevrolet TrailBlazer

1 Answer

Is the multifunction switch and the trun signal switch the same


I depends - it is considered a multifunction switch when the turn signals do multiple things. On Ford vehicles the switch generally controls wipers as well. If your turn signal switch has additional controls - then it is a multifunction switch.

May 27, 2011 | Ford Expedition Cars & Trucks

1 Answer

Where do I find the multifunction switch?


It is the switch on your steering column that runs the turn signals hazers high and low beams and wipers. The big lever that you use to turn your turn signals on is part of the switch and is replaced when you replace the multifunction switch. It is the whole thing.

Mar 12, 2011 | 1999 Dodge Caravan

1 Answer

How to change multifunction switch on 04 buick century


STEP BY STEP INSTRUCTION First, any time you work around the steeringcolumn you it is a must to disable the air bag system you will do this my disconnectingthe battery. After you disconnect the battery wait at least 5 minutes before proceeding. 1. Ifyou have tilt remove the tilt actuator arm by firmly pulling straight out. 2. Removethe upper and lower trim covers. 3. Removethe wire harness assembly from the wire harness strap. 4. Disconnect the turn signal andmultifunction switch assembly connector from the SIR system coil connector.This is alongside the steering column there is an 8mm bolt in the center of theconnector that must be removed to disconnect the connector halves. 5. Slide the 2 connectors of the turnsignal and multifunction switch assembly out of the bulkhead connector. With a smallscrewdriver slightly pry between the connectors to release them. 6. Removethe 2 pan head tapping screws and from the turn signal and multifunction switchassembly. 7. Removethe turn signal and multifunction switch assembly from the steering column tilthead assembly. INSTALLATION PROCEDURE 1. Installthe turn signal and multifunction switch assembly onto the steering column tilthead assembly. 2. Screwthe 2 pan head tapping screws and into the turn signal and multifunctionassembly.3. Slidethe 2 connectors of the turn signal and multifunction switch assembly into thebulkhead connector. 4. Connectthe turn signal and multifunction switch assembly connector to the SIR coilconnector. 5. Installthe wire harness assembly (1) into the wire harness strap (2). 6. Installthe upper and lower trim covers. 7. Installtilt actuator arm. 8. Reconnectthe battery.


Mar 01, 2011 | Buick Century Cars & Trucks

1 Answer

Turn signals will not automatically cancel


This is common for the turn signal/multifunction switch to do this. They have little plastis tabs that are hit when the steering is turned to cancel the signal. If those tabs have worn down or broken, the switch continues to work but will not cancel. Replace the switch if this is a major annoyance to you. Let me know if you need instructions or diagrams.

Apr 22, 2010 | 1999 Jeep Wrangler

2 Answers

Rear turn signals don't work, bulbs are good, front signals blink fast, at first only drivers side didn't work occasionally, now neither side works at all. What's wrong?


are you sure bulbs are good ?? double check bulbs also make sure there is a ground wire from your light fixture is grounded to the body near by this might be causing your problem .. usually if front ones blink fast rear bulbs are bad ... thanks Jerry holler if you need more.

Jan 29, 2009 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
2005 Dodge Magnum Logo

Related Topics:

991 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...