Question about 2001 Mitsubishi Eclipse Spyder

1 Answer

Manual trans removal on a 01 mits ecp spy gt. everything is taken off just wont come out

Posted by on

  • shawnriemer Apr 25, 2009

    it is the throw out bearing connected to the pressure plate fingers there a plug hole in the bottom of the bell housing need to remove it



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is the trow out bearing is connected to the pressure plate there is a plug in the bottom of the bell houseing need to remove for seporation not sure how to seperate have same problem but at least you no why you cant seperate it all i know for now

Posted on Apr 25, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My car transmission won't engage when I put it in any gear...... 03 mits galant

If automatic, could be toast, but at least remove trans pan and inspect filter, wiring and linkage. If stick shift, check linkage and clutch. Either trans could have broken u-joint in half shaft.

Jul 09, 2016 | Cars & Trucks

1 Answer

Replaced tcm and still wont shift or speed o wont work on 01 pt crusier

Call Chrysler you may have to have them program the trans computer I don't know but it sounds like that. Otherwise check your trans speed sensor it could be the problem

Aug 29, 2014 | Chrysler Pt Cruiser 01-09 Front

2 Answers

Cannot remove transmission

Did you remove the torque converter bolt's from the fly wheel, should be 4. You will have to turn the motor by hand to remove all the bolt's.

Jul 22, 2010 | 1999 Ford Escort

1 Answer

How do you replace the rear shocks in an 01 Toyota Celica gt


Apr 18, 2010 | 2001 Toyota Celica

1 Answer

1995 mitsubishi galant will not engage in any gear but park does keep it from rolling. Would this be because of the torque converter?

You have a 7th generation mit galant. These are great cars but they have one major weakness; the auto transmision dies. Generally you have to have the trans rebuilt or many owners swap ion a manual trans. There is a great web site for owner's of the mits galant. lots of great information about galants to include hwo to swap the auto trans for a manual. You want to go to and scroll down to 7 generation section of the forum Galants are great cars; I own 4 of them, all 7g

Feb 10, 2010 | 2002 Mitsubishi Galant

1 Answer

How to remove an automatic transmission 1992 nissan terrano

the motor and trans must be lowered thru the bottom of the car. repair manual goes into detail . it took me 10 hours to complete with new motor install. remove all wireing harness assemblies and lable.remove cover plate on bottom of bellhouseing ,this gives access to 4 bolts connecting the torque converter . turn crankshaft pully to rotate and access all 4 bolts.remove bellhouseing bolts and pull motor from trans. almost everything under the hood has to be taken apart and disambled.get the book! radiator,exhaust,motor mounts,altranator.powersterring ,wireing harness,cv half shafts. lower the motor with a cycle lift and jack the car up, block and pull the motor and trans out to disassemble. bag and lable all bolts tag and lable all parts and wire connections. most shops charge 600. bucks to do this and its well worth the money. this is a big job

Jan 11, 2010 | Nissan Pathfinder Cars & Trucks

1 Answer

Changing from 98 2.5 man.tranny,to 01 3.9

WOW. You want to put a 3.9 ltr V6 from a 2001 Dakota into a 1998 Dakota with a 2.5 ltr 4 cylinder? And you want to keep the manual trans? Have you considered what you will be using for a fuel and engine managment system? If you have a wrecked truck as a host vehicle then the changover may work. But it will take patience and a lot of work. I don't think the 4 cylinder trans will bolt up but I am not sure - never tried that. However that light duty trans will probably not handle the torque for very long even if it did bolt up. Your local Auto Salvage Yard will have a changeover guide and be able to tell you if that trans will fit either engine. My recommendation is to swap everthing and change that 98 to a 01, auto trans and everything.
Good Luck
Let me know how it goes?

Mar 08, 2009 | 1995 Dodge Dakota

1 Answer

Do i need to remove trans-axle to install engine

lower subframe its easy to do and drop engine out the bottom onto the floor

Jan 25, 2009 | 2001 Ford Focus

1 Answer

1996 mits galant auto trans

if the car is manual transmission could be throw out bearings or release bearing

Jul 01, 2008 | 1996 Mitsubishi Galant

Not finding what you are looking for?
2001 Mitsubishi Eclipse Spyder Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides