Question about 2000 Buick LeSabre

Open Question

My window fell off track on drv side of 2001 Buick Century.

I need information on how to remove the door panel on the driver side. The window somehow fell off track. I can hear the motor but the window will not come up. I need assistance.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Where is the fuel filter located for Buick Century 2001

The fuel filter is located underneath the car in front of the gas tank.
You have release the fuel pressure. Remove the fuel filler cap, locate the fuel test port on the fuel rail on the passenger side on the end of the right real fuel rail for a 3.1L engine.
3.8L engine yhr test port is located at the pressure regulator under the trim cover.

Posted on Sep 23, 2008

Ad
  • 3 Answers

SOURCE: How do I get the door panel off?

remove the screw behind the door panel. where you place your hand to pull the door closed there is a small plastic cover in the bottom lift this out and there are two bolts under there, remove them. then you should use a trim removal tool to pry the plastic panel away from the door. you will have to go down both sides and across the bottom. the window lift cable end has probably broken which lets the window slide down. purchase a new window motor and regulator assembly. it simply bolts in

Posted on Jan 21, 2009

csmock132
  • 4669 Answers

SOURCE: 2001 Buick Century shift solenoid

It is in the side cover on the valve body. The transmission needs to be removed to access the solenoids.

Posted on May 18, 2009

  • 1986 Answers

SOURCE: 99 Buick LeSabre, how do I remove driver side door panel to replace power window motor?

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: REMOVING A DOOR PANEL

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to repair drivers window


Remove door inner panel.. Look for why it fell .. It is off the lift track, probably something broke.. find broken part and replace or repair.. its not uncommon for window regulators to break.

May 31, 2014 | 2001 Pontiac Grand Am SE

1 Answer

Driver's side window is off the track and is lodged inside the door. How do I take off the door panel and put the window back on its track?


The window regulator is broken

Windows do not go off track

Just like your back doesn't go out

You remove a couple screws around the door handle
You may have to pry up the switch panel to get to some
of them
There are plastic fasteners around the outside of the door
panel that get pryed loose

You won't like doing that job, as the professsionals
don't want to do it either

Sep 21, 2011 | 2003 Buick Century

1 Answer

How to remove drivers door panel on 99 buick century . I need to see why power window will not roll all the way up. seems to be off track


GET SILACONE SPRAY AND WET FRONT AND REAR RUBBER TRACKS THE WINDOW RUNS IN LIBERALLY..IF IT THEN WORKS ...REPEAT EVERY 2 WEEKS..IF THIS DOESN'T HELP YOU PROBABLY NEED A NEW WINDOW MOTOR.

Mar 20, 2010 | 1999 Buick Century

1 Answer

My 2001 buick driver side switch does not work can it be tested both window switch and window motor without removing the door panel an how


Do a wiggle wire test at the door of the harness coming in at your door hinges before going too far since the wires have an attendancy of breaking there.

Mar 12, 2010 | 2001 Buick Century

1 Answer

The driver's side power window is stuck half way up on 1998 buick century limited. What is the problem?


It could be the fuse, does it go down? If not chk. fuse, if fuse ok, see if you can help it down by pushing down on window wile working switch, and also same wile trying to go up, if it don't work or if its slow chanses are the motor is tired and needs replaced or its lost power like bad switch or broken wire. there is also a chanse it came off the track in witch case the door panel will have to be removed.

Apr 14, 2009 | Buick Century Cars & Trucks

1 Answer

How do I get the door panel off?


remove the screw behind the door panel. where you place your hand to pull the door closed there is a small plastic cover in the bottom lift this out and there are two bolts under there, remove them. then you should use a trim removal tool to pry the plastic panel away from the door. you will have to go down both sides and across the bottom. the window lift cable end has probably broken which lets the window slide down. purchase a new window motor and regulator assembly. it simply bolts in

Dec 22, 2008 | 2002 Buick Century

1 Answer

REMOVING A DOOR PANEL


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Oct 02, 2008 | 2002 Buick Rendezvous

2 Answers

1990 buick centruty, driver door schematic (window regulator)


The first thing you need to do before buying any parts is to remove the door panel and find out exactly what is wrong, the motor is a gear reduction unit and even if the motor works it may still not drive the output gear. The door panel is held on by screws and hidden clips, pop off any panels or light fixtures on the door trim, under those you will find the hidden retainer screws, then gently pull door panel at edges to disengage feather style snaps.

Aug 26, 2008 | 1990 Buick Century

Not finding what you are looking for?
2000 Buick LeSabre Logo

Related Topics:

481 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...