Question about 2006 Hyundai Sonata
We have a Santro Xing and it came with its Hyundai Security system. When the car is unlocked, only the right indicators work and not the left. Where as while driving and when the hazard is on, all work but only with the security system it does not work. Even the left side front door, does not operate with central locking or with the remote locking. But using the key for that door you can lock it. but central locking does not work. What can i do about it?
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Door locks don't work
Disassemble the paneling on left side ,under the steering wheel. Remove all screws and pull out the panel until you can you can reach behind it to remove the two Black Relays, on the side closest to Steering wheel. Remove the Relay covers, Clean the contacts with a 1/8 fine strip of 600 wet/dry sand paper. Only place the paper between the contacts, and pull out while holding slight pressure on the relay Armature. Turn over the sandpaper and repeat once again. Very gently press the TOP resting contact pad closer to the armature, to lessen the gap between the contact points, so the armature doesn't have to travel as far to reach the closed contact position. Repeat the above with the other2nd Relay. Replace the covers, reinstall the relays And test the Door locks prior to buttoning up the paneling. Note, a pair of long needle nosed pliers will help in removing the relays. Just Grip the relay and rock in Forward and Backward as you apply upward pressure.
Posted on Oct 09, 2008
SOURCE: central locking
Resolving this problem will require removing the door panel in question, and checking for voltage at the solenoid when the unlock button is pressed.
If there is 12V at the positive wire to the solenoid, but the door does not attempt to unlock, you must replace the solenoid.
Doors are not fused individually, so the fact the other doors are operating properly rules out fuses.
Remove the door panel, and check for voltage - if there is no voltage, the wiring is suspect. This would require more in-depth troubleshooting - checking wires for continuity to ground, and overall continuity.
Start with the door. Re-post your findings and I can help you additionally.
Thanks for using FixYa - Your FiXyA rating is appreciated!!
Posted on Jan 22, 2009
follow the exhaust pipe from the motor. i beleive it is before the catylitic converter. screws into the side of the pipe and there are wires attached to it.
Posted on Feb 21, 2009
SOURCE: cant get indicators working
there is a gray block fuse under the hood that could control the light
take it out and take it to auto zone and have checked this good be the
easiest fix but it will cost about $25.00 for that fuse!
Posted on Apr 17, 2009
You are correct in your assumption about a relay... there are two relays. One is for 'LOCKING' the other is for 'UN-LOCKING.' They are both labeled as "LOCK" relays (1 & 2). You can verify if a relay is bad by swapping one with the other. If the problem moves to 'unlocking' the doors, but will NOW LOCK - the relay is bad. If not, further troubleshooting is necessary.
Posted on Jun 07, 2009
Tips for a great answer:
May 02, 2013 | Cars & Trucks
Mar 02, 2012 | 2005 Hyundai XG300
Aug 24, 2017 | Hyundai Accent Cars & Trucks
Jul 30, 2010 | 2003 Hyundai Santa Fe
Oct 14, 2009 | 2005 Hyundai XG300
Jul 12, 2009 | 2006 Hyundai Santa Fe
Jun 15, 2009 | 2005 Hyundai XG300
Feb 21, 2009 | 2005 Hyundai Accent
Feb 17, 2009 | 2005 Hyundai XG300
121 people viewed this question
Usually answered in minutes!