Question about 1995 GMC Jimmy

1 Answer

Brakelights and signal lights work but reverse lights come with brakes and flash when right signal is on how do i fix this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 469 Answers

Check the right hand lamp for water in the lens, or socket, also check wires and connections on the right light assembly, you have a short in or around that light.

Hope this is of some help.
Ed

Posted on Apr 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights rear blinkers quit working when turn signal is on flashes really fast


You simply have a burned out bulb or bulbs. With the key turned on turn on the directional for the left side and then the right side. Typically one bulb is blown and the opposite side works normally. Observe the normal side and note which is the flashing bulb. It is the flashing bulb on the other (malfunctioning) side that needs to be replaced. To replace the bulb you must remove the entire brakelight assembly, which isn't difficult. Open the trunk and locate the electrical harness that lines up with the brakelight assembly. Near the harness, locate the two (possibly three) nuts or wingnuts that attach the brakelight assembly to the car. Once the nuts are removed, the assembly can be pulled off the rear of the car. After replacing the bulb, be sure to test the operation of the new bulb before reassembling everthing.

Mar 18, 2015 | 2002 Ford Taurus

1 Answer

Third brake light stays on; brakelights very dim; radio, clock, flasher emblem on dash blink when turn signals are used; signals flash fast when brake pedal is applied.


Sounds like you have a short somewhere in the brake circuit. May be between the brakes and the blinkers in the brake lights.

Sep 19, 2011 | 1998 Oldsmobile Silhouette

2 Answers

No brake lights or turn signals on 1997 chevy lumina


Check the fuses..If ok ,,then most likely the signal switch..Your brake light circuit runs through the signal switch as well..Get someone to watch your brake lights to see if they come on..Now push the brake down and move your signal switch around and see if the brake light comes on intermittently..If so its definetly your switch

Sep 17, 2011 | 1997 Chevrolet Lumina

2 Answers

My brakelights don't work, but the turn signals do, the fuses were changed and the bulbs were changed


possible issues could be brake light switch not working, bulbs could be burnt, broken wire to rear lights

Feb 03, 2011 | 1998 Chevrolet Tahoe

2 Answers

Left turn signal doesnt work and my brakelights


  1. Check the fuse make sure it is not busted and also use a designated amp only.
  2. Check the bulb and the wires also.

Mar 28, 2010 | 1997 Chevrolet Lumina

1 Answer

Brake light, reverse light and turn signal issues


Hello. The symptoms you are describing are likely due to a poor ground. Temporarily install a new ground wire by securing a piece of copper wire to the frame with a self tapping screw. Use this ground wire along with the hot wire to see if each of these lights works. If it does, trace the ground wire back to the frame, unscrew it and clean up the metal with emery cloth so you reestablish a good ground.

Jan 28, 2010 | 2003 Ford Windstar

1 Answer

1988 ford thunderbird brake lights and turn signals not working


When this happens the problem is most likely the multi-funtion switch aka turn signal switch. Check to see if the 3rd brakelight comes on when the brake pedal is pushed. If so replace the MFS. The 3rd brakelight in late 80's fords bypasses the turnsignal switch.

Dec 29, 2008 | 1988 Ford Thunderbird

1 Answer

2005 and a half, Jetta 2.5 warning light inside tach display


I have the same problem, because it's difficult to see the rear brakelight halo when you are not at the right angle.  And, when my wife was driving in the Jetta--right in front of me--that's when I finally saw which brakelight was out (1/2 a halo).  (2006 Jetta 2.5). 

Jun 29, 2008 | 2005 Volkswagen Jetta

Not finding what you are looking for?
1995 GMC Jimmy Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...