Question about 1997 Toyota RAV4

1 Answer

Where are the Grease Fittings

I would like to know where the grease fittings are on a 1997 Toyota rav4, 4-door, It is also four wheel drive. Any help or suggestions would be great, thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

There arent any

Posted on Apr 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Do the front ball bearings have grease fittings for a 2005 Toyota Tacoma prerunner SR5?


if your talking wheel bearings then no these are supposed to be a sealed greased bearing from the factory and not grease able.

Aug 28, 2014 | Cars & Trucks

1 Answer

1989 Toyota Pickup grease locations?


use white lithium grease and the plugs are on just about every movable part on front end,ball joints, ty rods etc. on the driveline ends on transfer case to wheel, on drive line carrier bearing and on each u joint on each end of drive line and I think theres a couple on the rear end assembley somewhere.

Jan 20, 2013 | Toyota Pickup Cars & Trucks

1 Answer

Are there any grease fittings on/in the steering assemblies of the 97 Sebring?


Most front suspension parts have been "greased for life" for many years. No fittings.

Jun 25, 2012 | 1997 Chrysler Sebring

1 Answer

How many grease nipples does a ford maverick 1997 2.7td have and were are they located


By 1997 almost all cars were coming from the factory's without grease fittings, they had lifetime joints (haha). The only place you are likely to find any would be the front suspension, ball joints and tie rod ends. Most aftermarket suppliers still produce these parts with grease fittings so there are likely to be some fittings in the front end. Hope this helps.

Feb 21, 2012 | Cars & Trucks

1 Answer

How do i make sure i have greased all of my grease fittings


You should have one fitting on each upper and lower ball joint, (4 total), and you may or may not have fittings on each of the four tie rod ends. Don't overgrease any of them, they only need one or two strokes of the gun. I think that is all you have. Some cars have a fitting on each end of the upper A-arm, but GM generally uses a rubber bushing there instead, no grease required. The lower suspension arm to the frame is almost always a bushing and needs no grease.

You *might* have fittings on your driveshaft universal joints, although these need a special "needle" fitting to reach them. Most u-joints don't have fittings, however. If you have them, they are standard fittings located in one of the four inner "corners" of the joint, near the center.

Oct 10, 2010 | 1997 GMC Sierra

3 Answers

What places does my 1996 honda crv have grease nipples?


No factory grease fitting (zerks) on this vehicle. I am NOT a fan of this but I guess I'm just old school. BTW: my 2006 Toyota Tundra has 15 grease fittings under it.

May 29, 2010 | 1997 Honda CR-V

1 Answer

How many grease fitting are on a 2002 chev blazer, 4 wheel drive ?


Will very. Alot of the parts on the new cars are sealed and wont have grease fittings but when parts of steering and suspension are replaced then the have grease fitting so honestly it can very from car to car.

Feb 03, 2010 | 2002 Chevrolet Blazer

2 Answers

How do I grease the u-joints on the back of the drive shaft? on a 2000 toyota tacoma prerunner 2.7 liter


Grease gun with an adapter that allows you to get into a tighter space. Any auto parts place will sell these. Note, that a lot of replacement u-joints have grease fittings, as some stock ones don't require grease.

Nov 11, 2009 | 2000 Toyota Tacoma PreRunner

1 Answer

Grease fittings front end


certain durangos, have the fittings on the ends of the tie rods, and the ball joints, but it is different for 2 wheel drive and 4 wheel drive models... if you do not see the grease fittings on the ball joints, or the tie rods that means they can not be greased... check the boots on them tho, if there is any tearing, or the boot is missing or broken in any way, that part will need to be taken out and replaced...if the suspension part has no grease fitting in place, this indicates it is sealed and doesn't require periodic lubrication

Mar 14, 2009 | 2000 Dodge Durango

Not finding what you are looking for?
1997 Toyota RAV4 Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...