Question about 1995 Toyota Corolla

1 Answer

Need timing belt mark diagram for 95 corolla 4afe

Need timing belt mark diagram for 95 corolla 4afe 1.6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Master
  • 383 Answers

Malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.

Posted on May 06, 2009

  • kevin byrne
    kevin byrne Nov 24, 2013

    very helpfull thank you

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wanna install a cherry tiggo 2.0 sqr484 cambelt after the campulleys was removed by engineering


Bill Hackett provided this answer back in January 2014 for another Chery Tiggo owner.


SOURCE: need timing belt mark diagram for 95 corolla 4afe
malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.

May 17, 2017 | Cars & Trucks

3 Answers

Setting timing marks to get vehicle to start after engine overhaul


Timing marks setting Corolla 4A-FE.
Align the notch on the crankshaft pulley with the "0" mark on the timing belt lower cover.
25679262-y0srr1ownybx5goll4rgvnpm-5-0.jpg

With the crankshaft pulley being aligned with the 0 mark on the timing belt cover, the hole on the camshaft sprocket should exactly be in front of the notch of camshaft bracket.


25679262-y0srr1ownybx5goll4rgvnpm-5-2.jpg
Hope that works.

May 04, 2015 | 1998 Toyota Corolla

1 Answer

Timing chain installation


1996-1999 Toyota Corolla valve timing:
It is very easy to install the timing belt on 1997 Toyota Corolla. Do the following:
- Mark the numbers 1,2 and 3 on the spark plug wires with permanent marker or nail polish and remain the 4th one unmarked. This is necessary so that you can easily remember the spark plug wires order later on their original position.
- Remove the spark plugs so that the engine can easily be rotated.
- Rotate the crankshaft clockwise to align the v- groove mark on the crankshaft pulley with the 0 mark on the timing belt cover. If these marks are aligned the piston is always on the Top Dead Position (TDC).
25502648-okm0ksuj3f3lm2ubjq0dkjux-5-0.jpg

- To replace the timing belt remove the crankshaft pulley, upper and lower timing covers.
- Temporarily screw in the crankshaft bolt in its place to rotate the crankshaft with the spanner and align the v- groove of lower crankshaft gear with the index mark on the oil pump cover as shown in the following diagram.
- Inspect the cam shaft mark through the small hole on the cam shaft sprocket. The punch mark should be exactly behind the hole on the cam shaft sprocket as shown in the following diagram.


25502648-okm0ksuj3f3lm2ubjq0dkjux-5-2.jpg
- Loosen the timing bearing bolt, press the bearing forcefully against the spring with some suitable tool and lock it there temporarily.
- Remove the timing belt.
- Remove the timing bearing.
- Replace the new timing belt and bearing with the original.
- Install in the reverse order of dis-assembly.
NOTE: NEVER PUT EXTRA FORCE ON TIMING BEARING TO ADJUST THE TIMING BELT TENSION. JUST LOOSEN THE TIMING BEARING BOLT AND THE SPRING ATTACHED TO IT WILL PULL THE BEARING IT SELF WITH THE PRESET TENSION TO ADJUST THE TIMING BELT.
Thank you for visiting Fixya.

Mar 02, 2015 | 1997 Toyota Corolla

1 Answer

Need timing marks for 1993 1.6 Toyota Corola camshafts


If its the 1.6litre 4afe. Turn the crankshaft to TDC, ie. Tiny slit on the crank pulley should be straight underneath the 0deg mark. The cams, intake cam is driven off the exhaust cam by means of two gears. Installation marks. They have 4 holes in front of the gears. Front being closest to timing belt. Upon installation one hole in each gear should face upwards and the other holes should face each other between the gears. On the exhaust cam pulley there is a hole drilled through it, ie. timing mark. It should face up. Directly inline with the grove in the first cam cap. If you have 1.6litre 4age engine. Between cam gears and cylinder head there should be a plate. groves in cam gears should face the groves in the the plate.

Oct 19, 2014 | 1993 Toyota Corolla

1 Answer

How do I line up teh timing marks for a 1998 Toyota Corolla


turn the crank shaft clockwise until you can get the timing marks to line up

Feb 13, 2012 | Ford Ranger Cars & Trucks

3 Answers

Belt routing diagram for1999 Toyota Corolla


Thats a 98 belt routing same engine. 99 wouldnt load1021f4c.jpg

Jul 02, 2010 | 1999 Toyota Corolla

2 Answers

I am planning to replace the timing belt on my daughter's 95 Corolla and was wondering what I need to align where before removing the belt eg How do I find TDC? Camshaft pulley and Crankshaft pulley...


TDC is top dead center/ remove spark plug on cylinder no. 1/ rotate the crankshaft pulley using a socket wrench and power handle and check if the piston on your cylinder no. 1 reach the top center that is TDC/ remove timing belt cover and locate a synchronized marking on your camshaft and crankshaft pulley/ remove old timing belt/ install a new one but make sure that the mark on your camshaft and crankshaft is perfectly synchronized before putting the cover/ manually rotate the crankshaft pulley again and see if it rotates 360 deg. freely then you can be sure you did the job correctly.

Apr 06, 2010 | 1995 Toyota Corolla

2 Answers

Timing marks and how to set timing on toyota corrolla 1994 canm belt snapped and need to replace


Both 7afe and 4afe (engines for 93-97 Corollas) are non-interference engines. It's highly unlikely there is any damage to the valves.

Mar 18, 2010 | 1994 Toyota Corolla

1 Answer

You are changing the timing belt and you need o know where the timing marks are for the cam shaft and the crankshaft on a 1994 corolla Also how do you align the marks to put engine in time?


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1994 Toyota Corolla. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1994/make/toyota/model/corolla/1994_toyota_corolla_timing_belt_diagram_marks.htm

Sep 04, 2009 | 1994 Toyota Corolla

1 Answer

I need the schematics for the belts on my 1995


Look under the hood. Somewhere is a belt drive diagram. If you cannot find the belt routing sticker then you might just have to go to the parts store and have them order the manual for you specific car.

Aug 01, 2009 | 1995 Toyota Corolla

Not finding what you are looking for?
1995 Toyota Corolla Logo

4,920 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...