Question about 2001 Mazda MPV

Open Question

2001 Mazda MPV minivan. The ignition key can only be removed if you disconnect the 10 amp hazard fuse or unplug the 7 ohm load resistor that goes to the key lock solenoid ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: power windows on 2001 mazda mpv won't go up?

if you do not here the motor then its the regulator or motor that needs to be replaced/ cif you hear the motor check the control switch on the trim panle coould be just a five dollar part to replace/ Please rate my response thank you very much

Posted on Jan 31, 2009

Ad
emissionwiz
  • 76164 Answers

SOURCE: how to replace ignition coil mazda mpv 2004

I show $47 for each coil at rockauto.com here is the part #
STANDARD MOTOR PRODUCTS Part # UF406
here is a picture, is this the coil?
0d72734.jpg

Posted on Feb 14, 2009

  • 1 Answer

SOURCE: 2001 Mazda MPV upper front oxygen sensor change

I replaced this sensor about 6 months ago. (If this is the sensor that is located near the firewall on the exhaust manifold under the ignition coil.) The only way to easily replace it, is to remove the MAF and air filter assy. then remove the intake plenum, remove the ignition coil, and then you'll have access to the sensor. You'll need a sensor removal socket. If the socket slips around the hex of the sensor, then you'll need to use a regular deepwell socket and cut the cable from the top of the sensor, or use a combination wrench that will fit it.
The most difficult part of removing the intake plenum is getting the nut loose from the EGR valve. DO NOT just remove the two bolts holding it to the intake plenum. It will not line up correctly during re-assembly and may not seal tightly either.
This took about a Saturday to do. You'll need new plenum gaskets to replace the old. While your at it remove the throttle body and clean the carbon from the ports that lead to the EGR valve and replace that gasket as well. The gaskets will run about $30.

Posted on May 04, 2009

  • 1 Answer

SOURCE: owner manual mazda MPV 2001

www.jpnz.co.nz has translated owner manuals for sale .
about $50 nz i think it will cost you

Posted on Jan 21, 2010

bbbman78
  • 680 Answers

SOURCE: 96 mazda mpv minivan 165k mi. Ran fine until one

I was browsing unsolved problems. If you still have the problem, I'll try to help you. But it's going to be awhile trying to communicate back and forth. First...Check the engine for spark. Take off a plug wire and stick a screw driver in the wire end and place the metal part of the screw driver next to something on the van that's metal. Have someone crank it over for just a second or two and see if a small spark jumps from the screw driver to the metal part. I'll check back for your answer.

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is located the ground wire on mazda mpv 2001?


Your ground wire connection for the OBD2 connector is located under the dash just below and to the right of the heater controls. More likely that you dont have power to the connector. Check the 10 amp "ROOM" fuse in under dash fuse box.

May 08, 2016 | 2001 Mazda MPV

2 Answers

Security light on car tumbles but wont start


You can spray contact cleaner into the lock cylinder to clean the contacts that touch the resistor in the key. Many GM cars have orange wire for the security lock coming out of the steering column. I used a ohm meter to measure the resistance of my Pontiac's key and it was 3000 ohms. Having had trouble with mine I plan to cut the orange wire (actually two inside the orange sheath) and rig up a make and female plug/socket and one extra plug that will have a 3000 ohm resistor on it. When mine refuses to see the key I can always reach under the dash and unplug the key switch plug and pop in the fixed 3000 ohm plug to bypass (or satisfy) the security system. This will make it think it sees the key resistor though it actually is reading a plain resistor of the right value.

Feb 12, 2015 | 2002 Oldsmobile Alero

2 Answers

Key wont come out unless i turn battery off


A car can be stopped without a key, or if ignition switch fails. Put car in Park; look for 'fuel pump off' switch, in trunk under carpet. For manual ******, shift car into highest forward gear, release clutch while depressing brake pedal. --------------------------------------------------------------------------
Renault CAN Clip Diagnostic Interface

Dec 05, 2012 | 2003 Mazda MPV

1 Answer

2002 mazda mpv key won't come out


shift interlock is not working at shifter key wont turn to come out unless signal from switch tells it is in park.

Aug 03, 2012 | Cars & Trucks

1 Answer

I cannot turn my key past ACC setting and turn the car off in my 2002 MPV when the gear shift is in the P position. This also locks out my automatic doors for the middle seats. Is it the igination/key...


There is a small microswitch on the change lever assembly that has failed. This switch is used by the key interlock system to detect shift lever being put into Park position. The microswitch has not been available in the past as an indivfidual part but must be purchased with the entire change lever assembly.

May 01, 2011 | 2002 Mazda MPV

3 Answers

2002 mazda mpv, key stuck in ingition and it is in park , but the key wont turn all the way to lock, it will only go as far as acc?


Mazda MPV have problems with failing gear shift change assembly ( includes park sensor micro switch)

Pull the fuse for the hazard lights ( 10amp) - if the key comes out, then the switch is defective.

Fix the problem by installing a new change lever assembly - part number for 2000 and 2001 MPV's is LC62-46-10XE with MSRP of $246.90. 2002-2004 would be a LD47-46-10XB with MSRP of $250.40.

May 23, 2010 | 2000 Mazda MPV

1 Answer

96 mazda mpv minivan 165k mi. Ran fine until one day just died.Had towed home.3 mech.tried diagnose gave up wouldn't start-turns over-no start. Last mech.replaced timing belt&idle pulley. Still no...


I was browsing unsolved problems. If you still have the problem, I'll try to help you. But it's going to be awhile trying to communicate back and forth. First...Check the engine for spark. Take off a plug wire and stick a screw driver in the wire end and place the metal part of the screw driver next to something on the van that's metal. Have someone crank it over for just a second or two and see if a small spark jumps from the screw driver to the metal part. I'll check back for your answer.

Mar 05, 2010 | 1996 Mazda MPV

3 Answers

I have a Mazada 2002 mvp minivan. I can't turn my


My MPV has/had the same problem. Simply put the shifter up into Park and then press the outer end of the gear shifter away from you towards the dash/windshield until it clicks. While still depressing the shifter end, remove the key and it's in park. The microswitch is slightly out of adjustment. Good luck. I've been doing this for 2 and a half years and it's still working ok. Remember to let the attendant know if you leave the car with valet parking!

Apr 08, 2009 | 2002 Mazda MPV

2 Answers

Key stuck in ignition??


Try replacing the ignition switch.

Jun 26, 2008 | 2003 Mazda MPV

Not finding what you are looking for?
2001 Mazda MPV Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...