Question about 1999 Dodge Dakota

1 Answer

1999 dodge dakota manual transmission wont come out

I have all the bolts and skid plates and cross members off, and both drive lines off. The transmission will still not come off, HELP

Posted by on

  • wody Apr 19, 2009

    I will try to pry harder I guess. Do I need to support the engine?



  • wody Apr 19, 2009

    thank you!!! You would know if 8 bolts is all that there is?



×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

If the tranny housing is aluminum and the locating pins are steel they will corrode creating a bond.
It will come apart providing all bolts are removed and not easily!
When replacing tranny put antiseize on all aluminum and steel contact points to prevent future corrosion.
I hope this helps.

Posted on Apr 19, 2009

  • batsykline Apr 19, 2009

    You shouldnt have to but it might be wise to put some sort of support for safety

    If you question safety always take the time to get a jack stand or block of some kind

    Good Luck

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing drive shaft from 2001 Dodge Dakota


jack the rear of the truck up put jack stands or wooden blocks under the rear axle crawl under the truck you will find 4 bolts at the rear universal joint where it attaches to the rear end remove these 4 bolts and metal clips mark location of drive shaft in relation with where it bolts on the pinion flange use a sharpee or tape, now gentley pry the universal joint forward and lower rear of shaft , now wrap tape around the bearing caps so they don"t fall off this done pull the shaft out of the rear of transmission, one thing if your truck has 2 piece drive shaft you will have to unbolt the center hanger bearing too that requires 2 bolts that screw into the cross member to come out

Nov 22, 2015 | Dodge Cars & Trucks

1 Answer

How to remove the transmission on 1st generation dodge dakota 1991 4x4


one might think to unbolt it from the truck .cooling lines and any wiring drive shafts ,transfer case bell housing, flywheel, torque converter ,and cross member with a transmission jack in place under it . suggest you buy a repair manual and read it before starting

May 30, 2015 | 1991 Dodge Dakota

1 Answer

How the trans& transfercase bolt to frame


Are you wanting to remove the transmission and transfer case? If so, I advise that you have a good place to work and preferably a transmission jack. While fairly familiar with them, I haven't removed a transmission from a 4-wheel drive Dodge Dakota, but know they're considered to be one of the more difficult ones to do. Have you done this sort of thing before? That said, I can give you instructions. The transmission doesn't actually bolt to the frame. It bolts to the engine bell-housing and there'll be a rubber mount at the rear which probably fastens it to the cross-member with 2 bolts. There are several small things which have to be disconnected/removed, like wiring, the speedometer cable, both drive-shafts, etc. Let me know if you want to remove the transfer case and transmission or just the transfer case.

Dec 16, 2014 | 1994 Dodge Dakota Club Cab

1 Answer

Replace complete fuel line assembly in a Silverado z71 1500 4 whl. drive


Some of these drive shafts require removal of cross member to get them out. The fuel lines run up the back side of engine so removing the cross member will allow more room to gain access to the retaining hardware. jack up transmission and transfer case remove cross member lower down for access.

Dec 07, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

Torque spec for king nut on front spindle of 1999 2 wheel drive dodge dakota?


Unsure as to what you are calling the King nut but here are the torque specs for your front end.

Steering Gear-To-Cradle Bolt...........135 ft pnds
Steering Gear-To-Crossmember Bolt (Dakota 2 WD)..........190 ft pnds
Suspension Cradle Plate To-Cradle Attaching Bolt..............123 ft pnds
Tie Rod End-To-Steering Knuckle Nut Dakota (2WD) .............65 ft pnds
Tie Rod Lock Nut.....................55 ft pnds

Dec 08, 2009 | 1999 Dodge Dakota

1 Answer

Changing transmission filter and fluid on 1994 dodge dakota club


no , you will need a flat wrench and a hand driver and a allen wrench , i have a 95 4x4 i just did last week , takes about 25-30 mins from start to finish

Mar 07, 2009 | 1994 Dodge Dakota Club Cab

1 Answer

Transmission mount


Its bout the same for all rear wheel. Place a jack to support the transmission, remove the bolts from the mount and frame. If the tranny on a cross member then you should be able to remove the cross member by 4 bolts, then remove the mount from tranny and cross member.

Jan 19, 2009 | 1992 Dodge Ram 250

1 Answer

Tranny pan


you shouldn't have to but might , you could try to take the bolts that bolt the trans to the cross member and then lift on the trans and see if there is enough room to pull it out and get it back in without a problem , otherwise it might not pass the inside filter

Oct 09, 2008 | 1997 Dodge Dakota

1 Answer

What are the torque specs for 1990 dodge dakota front suspension.


call carquest or other parts house and ask them for the torque specs or a front end alignment shop.

Sep 24, 2008 | 1990 Dodge Dakota

Not finding what you are looking for?
1999 Dodge Dakota Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...